[RFC Home] [TEXT|PDF|HTML] [Tracker] [IPR] [Errata] [Info page]

PROPOSED STANDARD
Errata Exist
Network Working Group                                           E. Beili
Request for Comments: 4836                              Actelis Networks
Obsoletes: 3636                                               April 2007
Category: Standards Track


                   Definitions of Managed Objects for
               IEEE 802.3 Medium Attachment Units (MAUs)

Status of This Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The IETF Trust (2007).

Abstract

   This document defines a portion of the Management Information Base
   (MIB) for use with network management protocols in the Internet
   community.  In particular, it defines objects for managing IEEE 802.3
   Medium Attachment Units (MAUs).  This document obsoletes RFC 3636.
   It amends that specification by moving MAU type OBJECT-IDENTITY
   definitions and relevant textual conventions into a separate Internet
   Assigned Number Authority (IANA) maintained MIB module.  In addition,
   management information is added to enable support for Ethernet in the
   First Mile (EFM) and 10GBASE-CX4 MAUs.



















Beili                       Standards Track                     [Page 1]


RFC 4836                        MAU MIB                       April 2007


Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
   2.  The Internet-Standard Management Framework . . . . . . . . . .  3
   3.  Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .  4
     3.1.  Relationship to RFC 3636 . . . . . . . . . . . . . . . . .  4
     3.2.  Relationship to Other MIBs . . . . . . . . . . . . . . . .  5
       3.2.1.  Relationship to the Interfaces MIB . . . . . . . . . .  5
       3.2.2.  Relationship to the 802.3 Repeater MIB Module  . . . .  6
     3.3.  Management of Internal MAUs  . . . . . . . . . . . . . . .  6
     3.4.  Mapping of IEEE 802.3 Managed Objects  . . . . . . . . . .  6
     3.5.  Addition of New MAU Types  . . . . . . . . . . . . . . . .  9
       3.5.1.  dot3MauType OBJECT-IDENTITIES  . . . . . . . . . . . .  9
       3.5.2.  IANAifMauTypeListBits TEXTUAL-CONVENTION . . . . . . .  9
       3.5.3.  IANAifMauMediaAvailable TEXTUAL-CONVENTION . . . . . .  9
       3.5.4.  IANAifMauAutoNegCapBits TEXTUAL-CONVENTION . . . . . . 10
       3.5.5.  JackType TEXTUAL-CONVENTION  . . . . . . . . . . . . . 10
   4.  MAU MIB Definitions  . . . . . . . . . . . . . . . . . . . . . 10
   5.  IANA-Maintained MAU TC Definitions . . . . . . . . . . . . . . 46
   6.  Security Considerations  . . . . . . . . . . . . . . . . . . . 62
   7.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 63
   8.  Acknowledgments  . . . . . . . . . . . . . . . . . . . . . . . 63
   9.  References . . . . . . . . . . . . . . . . . . . . . . . . . . 64
     9.1.  Normative References . . . . . . . . . . . . . . . . . . . 64
     9.2.  Informative References . . . . . . . . . . . . . . . . . . 66


























Beili                       Standards Track                     [Page 2]


RFC 4836                        MAU MIB                       April 2007


1.  Introduction

   This document defines a portion of the Management Information Base
   (MIB) for use with network management protocols in the Internet
   community.  In particular, it defines objects for managing IEEE 802.3
   [IEEE802.3] Medium Attachment Units (MAUs).

   The previous version of this document, RFC 3636 [RFC3636], defined a
   single MIB module.  This document splits the original MIB module into
   two, putting frequently updated object identities and textual
   conventions into a separate, IANA-maintained MIB module, in order to
   decrease the need of updating the basic MAU MIB module.

   The first version of the IANA-maintained MIB module also extends the
   list of managed objects to support Ethernet in the First Mile (EFM)
   and 10GBASE-CX4 interfaces.

   Ethernet technology, as defined by the 802.3 Working Group of the
   IEEE, continues to evolve, with scalable increases in speed, new
   types of cabling and interfaces, and new features.  This evolution
   may require changes in the managed objects in order to reflect this
   new functionality.  This document, as with other documents issued by
   this working group, reflects a certain stage in the evolution of
   Ethernet technology.  In the future, this document might be revised,
   or new documents might be issued by the Ethernet Interfaces and Hub
   MIB Working Group, in order to reflect the evolution of Ethernet
   technology.

2.  The Internet-Standard Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to section 7 of
   RFC 3410 [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).
   Objects in the MIB are defined using the mechanisms defined in the
   Structure of Management Information (SMI).  This memo specifies a MIB
   module that is compliant to the SMIv2, which is described in STD 58,
   RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
   [RFC2580].

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].





Beili                       Standards Track                     [Page 3]


RFC 4836                        MAU MIB                       April 2007


3.  Overview

   Instances of these object types represent attributes of an IEEE 802.3
   MAU.  Several types of MAUs are defined in the IEEE 802.3 CSMA/CD
   standard [IEEE802.3].  These MAUs may be connected to IEEE 802.3
   repeaters or to 802.3 (Ethernet-like) interfaces.  For convenience,
   this document refers to these devices as "repeater MAUs" and
   "interface MAUs."

   The definitions presented here are based on Section 30.5, "Layer
   Management for 10 Mb/s, 100 Mb/s, 1000 Mb/s, and 10 Gb/s Medium
   Attachment Units (MAUs)", Section 30.6, "Management for link Auto-
   Negotiation", and Annex 30A, "GDMO Specifications for 802.3 managed
   object classes" of IEEE Std. 802.3-2005 [IEEE802.3].  This
   specification is intended to provide for management of all types of
   Ethernet/802.3 MAUs.

3.1.  Relationship to RFC 3636

   The management definitions provided in this document are intended to
   be a superset of those defined by RFC 3636 [RFC3636].

   In order to decrease the need of updating the basic MAU MIB module
   due to the new MAU type, Media Available state, Auto Negotiation
   capability and/or Jack type introduction, all relevant object
   identities and textual conventions have been moved to a separate,
   IANA-maintained MIB module IANA-MAU-MIB, the first version of which
   is defined in this document.  Thus when a new MAU type, Media
   Available state, Auto Negotiation capability, and/or Jack type is
   defined by the IEEE 802.3 working group, only the IANA-maintained
   module needs to be revised, leaving the basic MAU-MIB module defined
   in this document unchanged.

   In addition, the new definitions are added to the IANA-maintained MIB
   module, to support Ethernet in the First Mile (EFM) and 10GBASE-CX4
   interfaces, defined in IEEE Std 802.3ah-2004 [IEEE802.3ah] and IEEE
   Std 802.3ak-2004 [IEEE802.3ak] respectively, now part of IEEE Std
   802.3-2005 [IEEE802.3].

   It should be noted that the changes made in this revision will not be
   entirely backward-compatible with MIB modules that currently import
   MAU type object identity descriptors from the MAU-MIB; such modules
   will need to be revised to import those DESCRIPTORS from the IANA-
   MAU-MIB.  Similarly, any management applications that process the
   object identity definitions (e.g., to present the DESCRIPTION text to
   a user) will need to get those definitions from the IANA-MAU-MIB
   instead of the MAU-MIB.  While it is true that changes that require
   such adjustments are not strictly compliant with the SMIv2 rules



Beili                       Standards Track                     [Page 4]


RFC 4836                        MAU MIB                       April 2007


   governing MIB module revisions (see [RFC2578] Section 10), in this
   case continued high maintenance costs that would result from not
   making these changes make the deviation from the rules justified.  It
   should be noted that the working group was not able to find any
   examples of MIB modules or management applications that would
   actually be negatively affected by the changes.

3.2.  Relationship to Other MIBs

   It is assumed that an agent implementing MAU-MIB will also implement
   (at least) the 'system' group defined in the SNMPv2 MIB [RFC3418].
   The following sections identify other MIBs that such an agent should
   implement.

3.2.1.  Relationship to the Interfaces MIB

   The sections of this document that define interface MAU-related
   objects specify an extension to the Interfaces MIB [RFC2863].  An
   agent implementing these interface-MAU related objects MUST also
   implement the relevant groups of the ifCompliance3 MODULE-COMPLIANCE
   statement of the Interface MIB.  The value of the object ifMauIfIndex
   is the same as the value of 'ifIndex' used to instantiate the
   interface to which the given MAU is connected.

   It is REQUIRED that an agent implementing the interface-MAU related
   objects in the MAU-MIB will also fully comply with the
   dot3Compliance2 MODULE-COMPLIANCE statement of the Ethernet-like
   Interfaces MIB, [RFC3635].  Furthermore, when the interface-MAU
   related objects are used to manage a 10GBASE-W PHY -- i.e., when
   ifMauType is equal to dot3MauType10GigBaseW or any other 10GBASE-W
   variant -- then the agent MUST also support the Ethernet WAN
   Interface Sublayer (WIS) MIB [RFC3637] and must follow the interface
   layering model specified therein.  In that case the value of the
   object ifMauIfIndex is the same as the value of 'ifIndex' for the
   layer at the top of the stack, i.e., for the ifTable entry that has
   'ifType' equal to ethernetCsmacd(6).  If the interface-MAU related
   objects are used to manage a PHY that allows the MAU type to be
   changed dynamically, then the agent SHALL create ifTable,
   ifStackTable, and ifInvStackTable entries that pertain to the WIS
   when ifMauDefaultType is changed to a 10GBASEW variant (i.e., one of
   dot3MauType10GigBaseW, dot3MauType10GigBaseEW,
   dot3MauType10GigBaseLW, or dot3MauType10GigBaseSW) from any other
   type, and shall destroy the WIS-related entries when ifMauDefaultType
   is changed to a non- 10GBASE-W type.  The agent SHALL also change the
   values of 'ifConnectorPresent' and 'ifHighSpeed' in the ifTable entry
   indexed by ifMauIfIndex as specified in [RFC3635] and [RFC3637] when
   ifMauDefaultType is manipulated in this way, but SHALL NOT otherwise
   alter that entry.



Beili                       Standards Track                     [Page 5]


RFC 4836                        MAU MIB                       April 2007


   (Note that repeater ports are not represented as interfaces in the
   Interface MIB.)

3.2.2.  Relationship to the 802.3 Repeater MIB Module

   The section of this document that defines repeater MAU-related
   objects specifies an extension to the 802.3 Repeater MIB defined in
   [RFC2108].  An agent implementing these repeater-MAU related objects
   MUST also comply with the snmpRptrModCompl compliance statement of
   the 802.3 Repeater MIB module.

   The values of 'rpMauGroupIndex' and 'rpMauPortIndex' used to
   instantiate a repeater MAU variable SHALL be the same as the values
   of 'rptrPortGroupIndex' and 'rptrPortIndex' used to instantiate the
   port that the given MAU is connected to.

3.3.  Management of Internal MAUs

   In some situations, a MAU can be "internal" -- i.e., its
   functionality is implemented entirely within a device.  For example,
   a managed repeater may contain an internal repeater-MAU and/or an
   internal interface-MAU through which management communications
   originating on one of the repeater's external ports pass, in order to
   reach the management agent associated with the repeater.  Such
   internal MAUs may or may not be managed.  If they are managed,
   objects describing their attributes should appear in the appropriate
   MIB subtree: dot3RpMauBasicGroup for internal repeater-MAUs and
   dot3IfMauBasicGroup for internal interface-MAUs.

3.4.  Mapping of IEEE 802.3 Managed Objects

   This section contains the mapping between relevant managed objects
   (attributes) defined in [IEEE802.3] Clause 30, and managed objects
   defined in this document.

















Beili                       Standards Track                     [Page 6]


RFC 4836                        MAU MIB                       April 2007


   +----------------------------------+--------------------------------+
   | IEEE 802.3 Managed Object        | Corresponding SNMP Object      |
   +----------------------------------+--------------------------------+
   | oMAU                             |                                |
   +----------------------------------+--------------------------------+
   | .aMAUID                          | rpMauIndex or ifMauIndex or    |
   |                                  | broadMauIndex                  |
   +----------------------------------+--------------------------------+
   | .aMAUType                        | rpMauType or ifMauType         |
   +----------------------------------+--------------------------------+
   | .aMAUTypeList                    | ifMauTypeListBits              |
   +----------------------------------+--------------------------------+
   | .aMediaAvailable                 | rpMauMediaAvailable or         |
   |                                  | ifMauMediaAvailable            |
   +----------------------------------+--------------------------------+
   | .aLoseMediaCounter               | rpMauMediaAvailableStateExits  |
   |                                  | or                             |
   |                                  | ifMauMediaAvailableStateExits  |
   +----------------------------------+--------------------------------+
   | .aJabber                         | rpMauJabberState and           |
   |                                  | rpMauJabberingStateEnters or   |
   |                                  | ifMauJabberState and           |
   |                                  | ifMauJabberingStateEnters      |
   +----------------------------------+--------------------------------+
   | .aMAUAdminState                  | rpMauStatus or ifMauStatus     |
   +----------------------------------+--------------------------------+
   | .aBbMAUXmitRcvSplitType          | broadMauXmtRcvSplitType        |
   +----------------------------------+--------------------------------+
   | .aBroadbandFrequencies           | broadMauXmtCarrierFreq and     |
   |                                  | broadMauTranslationFreq        |
   +----------------------------------+--------------------------------+
   | .aFalseCarriers                  | rpMauFalseCarriers or          |
   |                                  | ifMauFalseCarriers             |
   +----------------------------------+--------------------------------+
   | .acResetMAU                      | rpMauStatus or ifMauStatus     |
   +----------------------------------+--------------------------------+
   | .acMAUAdminControl               | rpMauStatus or ifMauStatus     |
   +----------------------------------+--------------------------------+
   | .nJabber                         | rpMauJabberTrap or             |
   |                                  | ifMauJabberTrap                |
   +----------------------------------+--------------------------------+
   | oAutoNegotiation                 |                                |
   +----------------------------------+--------------------------------+
   | .aAutoNegID                      | ifMauIndex                     |
   +----------------------------------+--------------------------------+
   | .aAutoNegAdminState              | ifMauAutoNegAdminStatus        |
   +----------------------------------+--------------------------------+
   | .aAutoNegRemoteSignalling        | ifMauAutoNegRemoteSignalling   |



Beili                       Standards Track                     [Page 7]


RFC 4836                        MAU MIB                       April 2007


   | .aAutoNegAutoConfig              | ifMauAutoNegConfig             |
   +----------------------------------+--------------------------------+
   | .aAutoNegLocalTechnologyAbility  | ifMauAutoNegCapabilityBits     |
   +----------------------------------+--------------------------------+
   | .aAutoNegAdvertisedTechnologyAbi | ifMauAutoNegAdvertisedBits and |
   | lity                             | ifMauAutoNegRemoteFaultAdverti |
   |                                  | sed                            |
   +----------------------------------+--------------------------------+
   | .aAutoNegReceivedTechnologyAbili | ifMauAutoNegReceivedBits and   |
   | ty                               | ifMauAutoNegRemoteFaultReceive |
   |                                  | d                              |
   +----------------------------------+--------------------------------+
   | .acAutoNegRestartAutoConfig      | ifMauAutoNegRestart            |
   +----------------------------------+--------------------------------+
   | .acAutoNegAdminControl           | ifMauAutoNegAdminStatus        |
   +----------------------------------+--------------------------------+

              Table 1: Mapping of IEEE 802.3 Managed Objects

   The following IEEE 802.3 managed objects have not been included in
   the MAU-MIB for the following reasons.

   +------------------------------------+------------------------------+
   | IEEE 802.3 Managed Object          | Reason for exclusion         |
   +------------------------------------+------------------------------+
   | oMAU                               |                              |
   +------------------------------------+------------------------------+
   | .aIdleErrorCount                   | Only useful for 100BaseT2,   |
   |                                    | which is not widely          |
   |                                    | implemented.                 |
   +------------------------------------+------------------------------+
   | oAutoNegotiation                   |                              |
   +------------------------------------+------------------------------+
   | .aAutoNegLocalSelectorAbility      | Only needed for support of   |
   |                                    | isoethernet (802.9a), which  |
   |                                    | is not supported by MAU-MIB. |
   +------------------------------------+------------------------------+
   | .aAutoNegAdvertisedSelectorAbility |                              |
   +------------------------------------+------------------------------+
   | .aAutoNegReceivedSelectorAbility   |                              |
   +------------------------------------+------------------------------+

               Table 2: Unmapped IEEE 802.3 Managed Objects








Beili                       Standards Track                     [Page 8]


RFC 4836                        MAU MIB                       April 2007


3.5.  Addition of New MAU Types

3.5.1.  dot3MauType OBJECT-IDENTITIES

   The dot3MauType OBJECT IDENTIFIER and its OBJECT-IDENTITY definitions
   has been moved from the MAU-MIB into the IANA-maintained IANA-MAU-
   MIB, the first version of which is defined in this document.

   When a new IEEE 802.3 MAU is defined, IANA can re-issue a version of
   IANA-MAU-MIB with the new dot3MauType OBJECT-IDENTITY and its
   matching IANAifMauTypeListBits textual convention value and,
   possibly, with new IANAifMauMediaAvailable, IANAifMauAutoNegCapBits,
   and/or IANAifJackType values.

   An Expert Review, as defined in RFC 2434 [RFC2434], is REQUIRED for
   the addition of the new MAU, Media Available states, Auto Negotiation
   capabilities, and/or Jack types.

   In some cases, new MAU types may require additional managed objects
   or may have side effects on the behavior of existing managed objects.
   In such cases a standards-track specification (which may be a new
   document or a revision of this document) is also REQUIRED.  Any such
   document is REQUIRED to note any special properties of the MAU types
   that it defines - for example, side effects on the ifStackTable as
   noted in this document for 10GBASE-W MAUs.

3.5.2.  IANAifMauTypeListBits TEXTUAL-CONVENTION

   The syntax of ifMauTypeListBits is changed to be a textual
   convention, such that the enumerated integer values are now defined
   in the textual convention IANAifMauTypeListBits, which can be re-
   specified (with additional values, when defined by IEEE 802.3) in the
   IANA-maintained MIB module without issuing a new version of this
   document.

3.5.3.  IANAifMauMediaAvailable TEXTUAL-CONVENTION

   The syntax of ifMauMediaAvailable and rpMauMediaAvailable is changed
   to be a textual convention, such that the enumerated integer values
   are now defined in the textual convention IANAifMauMediaAvailable,
   which can be re-specified (with additional values, when defined by
   IEEE 802.3) in the IANA-maintained MIB module without issuing a new
   version of this document.








Beili                       Standards Track                     [Page 9]


RFC 4836                        MAU MIB                       April 2007


3.5.4.  IANAifMauAutoNegCapBits TEXTUAL-CONVENTION

   The syntax of ifMauAutoNegCapabilityBits,
   ifMauAutoNegCapAdvertisedBits, and ifMauAutoNegCapReceivedBits
   objects is changed to be a textual convention, such that the
   enumerated integer values are now defined in the textual convention
   IANAifMauAutoNegCapBits, which can be re-specified (with additional
   values, when defined by IEEE 802.3) in the IANA-maintained MIB module
   without issuing a new version of this document.

3.5.5.  JackType TEXTUAL-CONVENTION

   The JackType Textual Convention has been deprecated in favor of the
   IANAifJackType defined in the IANA-maintained MIB module, so the new
   Jack types can be added (when defined by IEEE 802.3) without issuing
   a new version of this document.

4.  MAU MIB Definitions

   MAU-MIB DEFINITIONS ::= BEGIN

     IMPORTS
       Counter32, Integer32, Counter64,
       OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE, mib-2
         FROM SNMPv2-SMI         -- RFC 2578
       TruthValue, AutonomousType, TEXTUAL-CONVENTION
         FROM SNMPv2-TC          -- RFC 2579
       OBJECT-GROUP, MODULE-COMPLIANCE, NOTIFICATION-GROUP
         FROM SNMPv2-CONF        -- RFC 2580
       InterfaceIndex
         FROM IF-MIB             -- RFC 2863
       IANAifMauTypeListBits, IANAifMauMediaAvailable,
       IANAifMauAutoNegCapBits, IANAifJackType
         FROM IANA-MAU-MIB
                          -- http://www.iana.org/assignments/ianamau-mib
       ;

     mauMod MODULE-IDENTITY
       LAST-UPDATED "200704210000Z"  -- April 21, 2007
       ORGANIZATION "IETF Ethernet Interfaces and Hub MIB Working Group"
       CONTACT-INFO
         "WG charter:
           http://www.ietf.org/html.charters/hubmib-charter.html

         Mailing Lists:
           General Discussion: hubmib@ietf.org
           To Subscribe: hubmib-request@ietf.org
           In Body: subscribe your_email_address



Beili                       Standards Track                    [Page 10]


RFC 4836                        MAU MIB                       April 2007


          Chair: Bert Wijnen
         Postal: Alcatel-Lucent
                 Schagen 33
                 3461 GL Linschoten
                 Netherlands
          Phone: +31-348-407-775
          EMail: bwijnen@alcatel-lucent.com

         Editor: Edward Beili
         Postal: Actelis Networks Inc.
                 25 Bazel St., P.O.B. 10173
                 Petach-Tikva 10173
                 Israel
            Tel: +972-3-924-3491
          EMail: edward.beili@actelis.com"

       DESCRIPTION
         "Management information for 802.3 MAUs.

         The following reference is used throughout this MIB module:

         [IEEE802.3] refers to:
            IEEE Std 802.3, 2005 Edition: 'IEEE Standard for Information
            technology - Telecommunications and information exchange
            between systems - Local and metropolitan area networks -
            Specific requirements - Part 3: Carrier sense multiple
            access with collision detection (CSMA/CD) access method and
            physical layer specifications'.

            Of particular interest is Clause 30, 'Management'.

         Copyright (C) The IETF Trust (2007).
         This version of this MIB module is part of RFC 4836;
         see the RFC itself for full legal notices."

       REVISION    "200704210000Z"  -- April 21, 2007
       DESCRIPTION "Updated to reference IANA maintaned textual
                   conventions for MAU types, Media Availability state,
                   Auto Negotiation capabilities, and jack types,
                   instead of using internally defined values.

                   This version is published as RFC 4836."

       REVISION    "200309190000Z"  -- September 19, 2003
       DESCRIPTION "Updated to include support for 10 Gb/s MAUs.
                   This resulted in the following revisions:
                   - Added OBJECT-IDENTITY definitions for
                     10 gigabit MAU types



Beili                       Standards Track                    [Page 11]


RFC 4836                        MAU MIB                       April 2007


                   - Added fiberLC jack type to JackType TC
                   - Extended ifMauTypeListBits with bits for
                     the 10 gigabit MAU types
                   - Added enumerations to ifMauMediaAvailable,
                     and updated its DESCRIPTION to reflect
                     behaviour at 10 Gb/s
                   - Added 64-bit version of ifMauFalseCarriers
                     and added mauIfGrpHCStats object group to
                     contain the new object
                   - Deprecated mauModIfCompl2 and replaced it
                     with mauModIfCompl3, which includes the new
                     object group

                    This version published as RFC 3636."

       REVISION    "199908240400Z" -- August 24, 1999
       DESCRIPTION "This version published as RFC 2668.  Updated
                   to include support for 1000 Mb/sec
                   MAUs and flow control negotiation."

       REVISION    "199710310000Z" -- October 31, 1997
       DESCRIPTION "Version published as RFC 2239."

       REVISION    "199309300000Z" -- September 30, 1993
       DESCRIPTION "Initial version, published as RFC 1515."

       ::= { snmpDot3MauMgt 6 }

      snmpDot3MauMgt OBJECT IDENTIFIER ::= { mib-2 26 }

      -- Textual Conventions

      JackType ::= TEXTUAL-CONVENTION
        STATUS      deprecated
        DESCRIPTION "********* THIS TC IS DEPRECATED **********

                    This TC has been deprecated in favour of
                    IANAifJackType.

                    Common enumeration values for repeater
                    and interface MAU jack types."
        SYNTAX      INTEGER {
                              other(1),
                              rj45(2),
                              rj45S(3), -- rj45 shielded
                              db9(4),
                              bnc(5),
                              fAUI(6),  -- female aui



Beili                       Standards Track                    [Page 12]


RFC 4836                        MAU MIB                       April 2007


                              mAUI(7),  -- male aui
                              fiberSC(8),
                              fiberMIC(9),
                              fiberST(10),
                              telco(11),
                              mtrj(12),  -- fiber MT-RJ
                              hssdc(13), -- fiber channel style-2
                              fiberLC(14)
                          }

      dot3RpMauBasicGroup
          OBJECT IDENTIFIER ::= { snmpDot3MauMgt 1 }
      dot3IfMauBasicGroup
          OBJECT IDENTIFIER ::= { snmpDot3MauMgt 2 }
      dot3BroadMauBasicGroup
          OBJECT IDENTIFIER ::= { snmpDot3MauMgt 3 }

      -- OIDs under the following branch are reserved for
      -- the IANA-MAU-MIB to assign as MAU type values:
      --                        { snmpDot3MauMgt 4 }

      dot3IfMauAutoNegGroup
          OBJECT IDENTIFIER ::= { snmpDot3MauMgt 5 }

      -- the following OID is the MODULE-IDENTITY value
      -- for this MIB module:   { snmpDot3MauMgt 6 }

      --
      -- The Basic Repeater MAU Table
      --

      rpMauTable OBJECT-TYPE
        SYNTAX      SEQUENCE OF RpMauEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION "Table of descriptive and status information
                    about the MAU(s) attached to the ports of a
                    repeater."
        ::= { dot3RpMauBasicGroup 1 }

      rpMauEntry OBJECT-TYPE
        SYNTAX      RpMauEntry
        MAX-ACCESS  not-accessible
        STATUS      current
        DESCRIPTION "An entry in the table, containing information
                    about a single MAU."
        INDEX       { rpMauGroupIndex,
                      rpMauPortIndex,



Beili                       Standards Track                    [Page 13]


RFC 4836                        MAU MIB                       April 2007


                      rpMauIndex
                    }
        ::= { rpMauTable 1 }

      RpMauEntry ::=
        SEQUENCE {
            rpMauGroupIndex                     Integer32,
            rpMauPortIndex                      Integer32,
            rpMauIndex                          Integer32,
            rpMauType                           AutonomousType,
            rpMauStatus                         INTEGER,
            rpMauMediaAvailable                 IANAifMauMediaAvailable,
            rpMauMediaAvailableStateExits       Counter32,
            rpMauJabberState                    INTEGER,
            rpMauJabberingStateEnters           Counter32,
            rpMauFalseCarriers                  Counter32
      }

      rpMauGroupIndex OBJECT-TYPE
        SYNTAX      Integer32 (1..2147483647)
        MAX-ACCESS  read-only  -- read-only since originally an
                               -- SMIv1 index
        STATUS      current
        DESCRIPTION "This variable uniquely identifies the group
                    containing the port to which the MAU described
                    by this entry is connected.

                    Note:  In practice, a group will generally be
                    a field-replaceable unit (i.e., module, card,
                    or board) that can fit in the physical system
                    enclosure, and the group number will correspond
                    to a number marked on the physical enclosure.

                    The group denoted by a particular value of this
                    object is the same as the group denoted by the
                    same value of rptrGroupIndex."
        REFERENCE   "RFC 2108, rptrGroupIndex."
        ::= { rpMauEntry 1 }

      rpMauPortIndex OBJECT-TYPE
        SYNTAX      Integer32 (1..2147483647)
        MAX-ACCESS  read-only  -- read-only since originally an
                               -- SMIv1 index
        STATUS      current
        DESCRIPTION "This variable uniquely identifies the repeater
                    port within group rpMauGroupIndex to which the
                    MAU described by this entry is connected."
        REFERENCE   "RFC 2108, rptrPortIndex."



Beili                       Standards Track                    [Page 14]


RFC 4836                        MAU MIB                       April 2007


        ::= { rpMauEntry 2 }

      rpMauIndex OBJECT-TYPE
        SYNTAX      Integer32 (1..2147483647)
        MAX-ACCESS  read-only  -- read-only since originally an
                               -- SMIv1 index
        STATUS      current
        DESCRIPTION "This variable uniquely identifies the MAU
                    described by this entry from among other
                    MAUs connected to the same port
                    (rpMauPortIndex)."
        REFERENCE   "[IEEE802.3], 30.5.1.1.1, aMAUID."
        ::= { rpMauEntry 3 }

      rpMauType OBJECT-TYPE
        SYNTAX      AutonomousType
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION "This object identifies the MAU type.  Values for
                    standard IEEE 802.3 MAU types are defined in the
                    IANA maintained IANA-MAU-MIB module, as
                    OBJECT-IDENTITIES of dot3MauType.
                    If the MAU type is unknown, the object identifier
                    zeroDotZero is returned."
        REFERENCE   "[IEEE802.3], 30.5.1.1.2, aMAUType."
        ::= { rpMauEntry 4 }

      rpMauStatus OBJECT-TYPE
          SYNTAX      INTEGER {
                          other(1),
                          unknown(2),
                          operational(3),
                          standby(4),
                          shutdown(5),
                          reset(6)
                      }
          MAX-ACCESS  read-write
          STATUS      current
          DESCRIPTION "The current state of the MAU.  This object MAY
                      be implemented as a read-only object by those
                      agents and MAUs that do not implement software
                      control of the MAU state.  Some agents may not
                      support setting the value of this object to some
                      of the enumerated values.

                      The value other(1) is returned if the MAU is in
                      a state other than one of the states 2 through
                      6.



Beili                       Standards Track                    [Page 15]


RFC 4836                        MAU MIB                       April 2007


                      The value unknown(2) is returned when the MAU's
                      true state is unknown; for example, when it is
                      being initialized.

                      A MAU in the operational(3) state is fully
                      functional; it operates, and passes signals to its
                      attached DTE or repeater port in accordance to
                      its specification.

                      A MAU in standby(4) state forces DI and CI to
                      idle, and the media transmitter to idle or fault,
                      if supported.  Standby(4) mode only applies to
                      link type MAUs.  The state of
                      rpMauMediaAvailable is unaffected.

                      A MAU in shutdown(5) state assumes the same
                      condition on DI, CI, and the media transmitter,
                      as though it were powered down or not connected.
                      The MAU MAY return other(1) value for the
                      rpMauJabberState and rpMauMediaAvailable objects
                      when it is in this state.  For an AUI, this
                      state will remove power from the AUI.

                      Setting this variable to the value reset(6)
                      resets the MAU in the same manner as a
                      power-off, power-on cycle of at least one-half
                      second would.  The agent is not required to
                      return the value reset(6).

                      Setting this variable to the value
                      operational(3), standby(4), or shutdown(5)
                      causes the MAU to assume the respective state,
                      except that setting a mixing-type MAU or an AUI
                      to standby(4) will cause the MAU to enter the
                      shutdown state."
          REFERENCE   "[IEEE802.3], 30.5.1.1.7, aMAUAdminState,
                      30.5.1.2.2, acMAUAdminControl, and 30.5.1.2.1,
                      acResetMAU."
          ::= { rpMauEntry 5 }

      rpMauMediaAvailable OBJECT-TYPE
          SYNTAX      IANAifMauMediaAvailable
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "This object identifies Media Available state of
                      the MAU, complementary to the rpMauStatus.  Values
                      for the standard IEEE 802.3 Media Available states
                      are defined in the IANA maintained IANA-MAU-MIB



Beili                       Standards Track                    [Page 16]


RFC 4836                        MAU MIB                       April 2007


                      module, as IANAifMauMediaAvailable TC."
          REFERENCE   "[IEEE802.3], 30.5.1.1.4, aMediaAvailable."
          ::= { rpMauEntry 6 }

      rpMauMediaAvailableStateExits OBJECT-TYPE
          SYNTAX      Counter32
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "A count of the number of times that
                      rpMauMediaAvailable for this MAU instance leaves
                      the state available(3).

                      Discontinuities in the value of this counter can
                      occur at re-initialization of the management
                      system and at other times, as indicated by the
                      value of rptrMonitorPortLastChange."
          REFERENCE   "[IEEE802.3], 30.5.1.1.5, aLoseMediaCounter.
                      RFC 2108, rptrMonitorPortLastChange"
          ::= { rpMauEntry 7 }

      rpMauJabberState OBJECT-TYPE
          SYNTAX      INTEGER {
                          other(1),
                          unknown(2),
                          noJabber(3),
                          jabbering(4)
                      }
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "The value other(1) is returned if the jabber
                      state is not 2, 3, or 4.  The agent MUST always
                      return other(1) for MAU type dot3MauTypeAUI.

                      The value unknown(2) is returned when the MAU's
                      true state is unknown; for example, when it is
                      being initialized.

                      If the MAU is not jabbering the agent returns
                      noJabber(3).  This is the 'normal' state.

                      If the MAU is in jabber state the agent returns
                      the jabbering(4) value."
          REFERENCE "[IEEE802.3], 30.5.1.1.6, aJabber.jabberFlag."
          ::= { rpMauEntry 8 }

      rpMauJabberingStateEnters OBJECT-TYPE
          SYNTAX      Counter32
          MAX-ACCESS  read-only



Beili                       Standards Track                    [Page 17]


RFC 4836                        MAU MIB                       April 2007


          STATUS      current
          DESCRIPTION "A count of the number of times that
                      mauJabberState for this MAU instance enters the
                      state jabbering(4).  For MAUs of type
                      dot3MauTypeAUI, dot3MauType100BaseT4,
                      dot3MauType100BaseTX, dot3MauType100BaseFX, and
                      all 1000Mbps types, this counter will always
                      indicate zero.

                      Discontinuities in the value of this counter can
                      occur at re-initialization of the management
                      system and at other times, as indicated by the
                      value of rptrMonitorPortLastChange."
          REFERENCE   "[IEEE802.3], 30.5.1.1.6, aJabber.jabberCounter.
                      RFC 2108, rptrMonitorPortLastChange"
          ::= { rpMauEntry 9 }

      rpMauFalseCarriers OBJECT-TYPE
          SYNTAX      Counter32
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "A count of the number of false carrier events
                      during IDLE in 100BASE-X links.  This counter
                      does not increment at the symbol rate.  It can
                      increment after a valid carrier completion at a
                      maximum rate of once per 100 ms until the next
                      carrier event.

                      This counter increments only for MAUs of type
                      dot3MauType100BaseT4, dot3MauType100BaseTX,
                      dot3MauType100BaseFX, and all 1000Mbps types.

                      For all other MAU types, this counter will
                      always indicate zero.

                      The approximate minimum time for rollover of
                      this counter is 7.4 hours.

                      Discontinuities in the value of this counter can
                      occur at re-initialization of the management
                      system and at other times, as indicated by the
                      value of rptrMonitorPortLastChange."
          REFERENCE   "[IEEE802.3], 30.5.1.1.10, aFalseCarriers.
                      RFC 2108, rptrMonitorPortLastChange"
          ::= { rpMauEntry 10 }

      -- The rpJackTable applies to MAUs attached to repeaters
      -- which have one or more external jacks (connectors).



Beili                       Standards Track                    [Page 18]


RFC 4836                        MAU MIB                       April 2007


      rpJackTable OBJECT-TYPE
          SYNTAX      SEQUENCE OF RpJackEntry
          MAX-ACCESS  not-accessible
          STATUS      current
          DESCRIPTION "Information about the external jacks attached
                      to MAUs attached to the ports of a repeater."
          ::= { dot3RpMauBasicGroup 2 }

      rpJackEntry OBJECT-TYPE
          SYNTAX      RpJackEntry
          MAX-ACCESS  not-accessible
          STATUS      current
          DESCRIPTION "An entry in the table, containing information
                      about a particular jack."
          INDEX       { rpMauGroupIndex,
                        rpMauPortIndex,
                        rpMauIndex,
                        rpJackIndex
                      }
          ::= { rpJackTable 1 }

      RpJackEntry ::=
          SEQUENCE {
              rpJackIndex                         Integer32,
              rpJackType                          IANAifJackType
          }

      rpJackIndex OBJECT-TYPE
          SYNTAX      Integer32 (1..2147483647)
          MAX-ACCESS  not-accessible
          STATUS      current
          DESCRIPTION "This variable uniquely identifies the jack
                      described by this entry from among other jacks
                      attached to the same MAU (rpMauIndex)."
          ::= { rpJackEntry 1 }

      rpJackType OBJECT-TYPE
          SYNTAX      IANAifJackType
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "The jack connector type, as it appears on the
                      outside of the system."
          ::= { rpJackEntry 2 }

      --
      -- The Basic Interface MAU Table
      --




Beili                       Standards Track                    [Page 19]


RFC 4836                        MAU MIB                       April 2007


      ifMauTable OBJECT-TYPE
          SYNTAX      SEQUENCE OF IfMauEntry
          MAX-ACCESS  not-accessible
          STATUS      current
          DESCRIPTION "Table of descriptive and status information
                      about MAU(s) attached to an interface."
          ::= { dot3IfMauBasicGroup 1 }

      ifMauEntry OBJECT-TYPE
          SYNTAX      IfMauEntry
          MAX-ACCESS  not-accessible
          STATUS      current
          DESCRIPTION "An entry in the table, containing information
                      about a single MAU."
          INDEX       { ifMauIfIndex,
                        ifMauIndex
                      }
          ::= { ifMauTable 1 }

      IfMauEntry ::=
          SEQUENCE {
              ifMauIfIndex                      InterfaceIndex,
              ifMauIndex                        Integer32,
              ifMauType                         AutonomousType,
              ifMauStatus                       INTEGER,
              ifMauMediaAvailable               IANAifMauMediaAvailable,
              ifMauMediaAvailableStateExits     Counter32,
              ifMauJabberState                  INTEGER,
              ifMauJabberingStateEnters         Counter32,
              ifMauFalseCarriers                Counter32,
              ifMauTypeList                     Integer32,
              ifMauDefaultType                  AutonomousType,
              ifMauAutoNegSupported             TruthValue,
              ifMauTypeListBits                 IANAifMauTypeListBits,
              ifMauHCFalseCarriers              Counter64
          }

      ifMauIfIndex OBJECT-TYPE
          SYNTAX      InterfaceIndex
          MAX-ACCESS  read-only  -- read-only since originally an
                                 -- SMIv1 index
          STATUS      current
          DESCRIPTION "This variable uniquely identifies the interface
                      to which the MAU described by this entry is
                      connected."
          REFERENCE   "RFC 2863, ifIndex"
          ::= { ifMauEntry 1 }




Beili                       Standards Track                    [Page 20]


RFC 4836                        MAU MIB                       April 2007


      ifMauIndex OBJECT-TYPE
          SYNTAX      Integer32 (1..2147483647)
          MAX-ACCESS  read-only  -- read-only since originally an
                                 -- SMIv1 index
          STATUS      current
          DESCRIPTION "This variable uniquely identifies the MAU
                      described by this entry from among other MAUs
                      connected to the same interface (ifMauIfIndex)."
          REFERENCE   "[IEEE802.3], 30.5.1.1.1, aMAUID."
          ::= { ifMauEntry 2 }

      ifMauType OBJECT-TYPE
        SYNTAX      AutonomousType
        MAX-ACCESS  read-only
        STATUS      current
        DESCRIPTION "This object identifies the MAU type.  Values for
                    standard IEEE 802.3 MAU types are defined in the
                    IANA maintained IANA-MAU-MIB module, as
                    OBJECT-IDENTITIES of dot3MauType.
                    If the MAU type is unknown, the object identifier
                    zeroDotZero is returned.

                    This object represents the operational type of
                    the MAU, as determined by either 1) the result
                    of the auto-negotiation function or 2) if
                    auto-negotiation is not enabled or is not
                    implemented for this MAU, by the value of the
                    object ifMauDefaultType.  In case 2), a set to
                    the object ifMauDefaultType will force the MAU
                    into the new operating mode."
        REFERENCE   "[IEEE802.3], 30.5.1.1.2, aMAUType."
        ::= { ifMauEntry 3 }

      ifMauStatus OBJECT-TYPE
          SYNTAX      INTEGER {
                          other(1),
                          unknown(2),
                          operational(3),
                          standby(4),
                          shutdown(5),
                          reset(6)
                      }
          MAX-ACCESS  read-write
          STATUS      current
          DESCRIPTION "The current state of the MAU.  This object MAY
                      be implemented as a read-only object by those
                      agents and MAUs that do not implement software
                      control of the MAU state.  Some agents may not



Beili                       Standards Track                    [Page 21]


RFC 4836                        MAU MIB                       April 2007


                      support setting the value of this object to some
                      of the enumerated values.

                      The value other(1) is returned if the MAU is in
                      a state other than one of the states 2 through
                      6.

                      The value unknown(2) is returned when the MAU's
                      true state is unknown; for example, when it is
                      being initialized.

                      A MAU in the operational(3) state is fully
                      functional; it operates, and passes signals to its
                      attached DTE or repeater port in accordance to
                      its specification.

                      A MAU in standby(4) state forces DI and CI to
                      idle and the media transmitter to idle or fault,
                      if supported.  Standby(4) mode only applies to
                      link type MAUs.  The state of
                      ifMauMediaAvailable is unaffected.

                      A MAU in shutdown(5) state assumes the same
                      condition on DI, CI, and the media transmitter,
                      as though it were powered down or not connected.
                      The MAU MAY return other(1) value for the
                      ifMauJabberState and ifMauMediaAvailable objects
                      when it is in this state.  For an AUI, this
                      state will remove power from the AUI.

                      Setting this variable to the value reset(6)
                      resets the MAU in the same manner as a
                      power-off, power-on cycle of at least one-half
                      second would.  The agent is not required to
                      return the value reset(6).

                      Setting this variable to the value
                      operational(3), standby(4), or shutdown(5)
                      causes the MAU to assume the respective state,
                      except that setting a mixing-type MAU or an AUI
                      to standby(4) will cause the MAU to enter the
                      shutdown state."
          REFERENCE   "[IEEE802.3], 30.5.1.1.7, aMAUAdminState,
                      30.5.1.2.2, acMAUAdminControl, and 30.5.1.2.1,
                      acResetMAU."
          ::= { ifMauEntry 4 }

      ifMauMediaAvailable OBJECT-TYPE



Beili                       Standards Track                    [Page 22]


RFC 4836                        MAU MIB                       April 2007


          SYNTAX      IANAifMauMediaAvailable
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "This object identifies Media Available state of
                      the MAU, complementary to the ifMauStatus.  Values
                      for the standard IEEE 802.3 Media Available states
                      are defined in the IANA maintained IANA-MAU-MIB
                      module, as IANAifMauMediaAvailable TC."
          REFERENCE   "[IEEE802.3], 30.5.1.1.4, aMediaAvailable."
          ::= { ifMauEntry 5 }

      ifMauMediaAvailableStateExits OBJECT-TYPE
          SYNTAX      Counter32
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "A count of the number of times that
                      ifMauMediaAvailable for this MAU instance leaves
                      the state available(3).

                      Discontinuities in the value of this counter can
                      occur at re-initialization of the management
                      system and at other times, as indicated by the
                      value of ifCounterDiscontinuityTime."
          REFERENCE   "[IEEE802.3], 30.5.1.1.5, aLoseMediaCounter.
                      RFC 2863, ifCounterDiscontinuityTime."
          ::= { ifMauEntry 6 }

      ifMauJabberState OBJECT-TYPE
          SYNTAX      INTEGER {
                          other(1),
                          unknown(2),
                          noJabber(3),
                          jabbering(4)
                      }
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "The value other(1) is returned if the jabber
                      state is not 2, 3, or 4.  The agent MUST always
                      return other(1) for MAU type dot3MauTypeAUI.

                      The value unknown(2) is returned when the MAU's
                      true state is unknown; for example, when it is
                      being initialized.

                      If the MAU is not jabbering the agent returns
                      noJabber(3).  This is the 'normal' state.

                      If the MAU is in jabber state the agent returns



Beili                       Standards Track                    [Page 23]


RFC 4836                        MAU MIB                       April 2007


                      the jabbering(4) value."
          REFERENCE   "[IEEE802.3], 30.5.1.1.6, aJabber.jabberFlag."
          ::= { ifMauEntry 7 }

      ifMauJabberingStateEnters OBJECT-TYPE
          SYNTAX      Counter32
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "A count of the number of times that
                      mauJabberState for this MAU instance enters the
                      state jabbering(4).  This counter will always
                      indicate zero for MAUs of type dot3MauTypeAUI
                      and those of speeds above 10Mbps.

                      Discontinuities in the value of this counter can
                      occur at re-initialization of the management
                      system and at other times, as indicated by the
                      value of ifCounterDiscontinuityTime."
          REFERENCE   "[IEEE802.3], 30.5.1.1.6, aJabber.jabberCounter.
                      RFC 2863, ifCounterDiscontinuityTime."
          ::= { ifMauEntry 8 }

      ifMauFalseCarriers OBJECT-TYPE
          SYNTAX      Counter32
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "A count of the number of false carrier events
                      during IDLE in 100BASE-X and 1000BASE-X links.

                      For all other MAU types, this counter will
                      always indicate zero.  This counter does not
                      increment at the symbol rate.

                      It can increment after a valid carrier
                      completion at a maximum rate of once per 100 ms
                      for 100BASE-X and once per 10us for 1000BASE-X
                      until the next CarrierEvent.

                      This counter can roll over very quickly.  A
                      management station is advised to poll the
                      ifMauHCFalseCarriers instead of this counter in
                      order to avoid loss of information.

                      Discontinuities in the value of this counter can
                      occur at re-initialization of the management
                      system and at other times, as indicated by the
                      value of ifCounterDiscontinuityTime."
          REFERENCE   "[IEEE802.3], 30.5.1.1.10, aFalseCarriers.



Beili                       Standards Track                    [Page 24]


RFC 4836                        MAU MIB                       April 2007


                      RFC 2863, ifCounterDiscontinuityTime."
          ::= { ifMauEntry 9 }

      ifMauTypeList OBJECT-TYPE
          SYNTAX      Integer32
          MAX-ACCESS  read-only
          STATUS      deprecated
          DESCRIPTION "********* THIS OBJECT IS DEPRECATED **********

                      This object has been deprecated in favour of
                      ifMauTypeListBits.

                      A value that uniquely identifies the set of
                      possible IEEE 802.3 types that the MAU could be.
                      The value is a sum that initially takes the
                      value zero.  Then, for each type capability of
                      this MAU, 2 raised to the power noted below is
                      added to the sum.  For example, a MAU that has
                      the capability to be only 10BASE-T would have a
                      value of 512 (2**9).  In contrast, a MAU that
                      supports both 10Base-T (full duplex) and
                      100BASE-TX (full duplex) would have a value of
                      ((2**11) + (2**16)), or 67584.

                      The powers of 2 assigned to the capabilities are
                      these:

                      Power  Capability
                        0      other or unknown
                        1      AUI
                        2      10BASE-5
                        3      FOIRL
                        4      10BASE-2
                        5      10BASE-T duplex mode unknown
                        6      10BASE-FP
                        7      10BASE-FB
                        8      10BASE-FL duplex mode unknown
                        9      10BROAD36
                       10      10BASE-T  half duplex mode
                       11      10BASE-T  full duplex mode
                       12      10BASE-FL half duplex mode
                       13      10BASE-FL full duplex mode
                       14      100BASE-T4
                       15      100BASE-TX half duplex mode
                       16      100BASE-TX full duplex mode
                       17      100BASE-FX half duplex mode
                       18      100BASE-FX full duplex mode
                       19      100BASE-T2 half duplex mode



Beili                       Standards Track                    [Page 25]


RFC 4836                        MAU MIB                       April 2007


                       20      100BASE-T2 full duplex mode

                      If auto-negotiation is present on this MAU, this
                      object will map to ifMauAutoNegCapability."
          ::= { ifMauEntry 10 }

      ifMauDefaultType OBJECT-TYPE
          SYNTAX      AutonomousType
          MAX-ACCESS  read-write
          STATUS      current
          DESCRIPTION "This object identifies the default
                      administrative baseband MAU type to be used in
                      conjunction with the operational MAU type
                      denoted by ifMauType.

                      The set of possible values for this object is
                      the same as the set defined for the ifMauType
                      object.

                      This object represents the
                      administratively-configured type of the MAU.  If
                      auto-negotiation is not enabled or is not
                      implemented for this MAU, the value of this
                      object determines the operational type of the
                      MAU.  In this case, a set to this object will
                      force the MAU into the specified operating mode.

                      If auto-negotiation is implemented and enabled
                      for this MAU, the operational type of the MAU
                      is determined by auto-negotiation, and the value
                      of this object denotes the type to which the MAU
                      will automatically revert if/when
                      auto-negotiation is later disabled.

                      NOTE TO IMPLEMENTORS:  It may be necessary to
                      provide for underlying hardware implementations
                      which do not follow the exact behavior specified
                      above.  In particular, when
                      ifMauAutoNegAdminStatus transitions from enabled
                      to disabled, the agent implementation MUST
                      ensure that the operational type of the MAU (as
                      reported by ifMauType) correctly transitions to
                      the value specified by this object, rather than
                      continuing to operate at the value earlier
                      determined by the auto-negotiation function."
          REFERENCE   "[IEEE802.3], 30.5.1.1.1, aMAUID, and 22.2.4.1.4."
          ::= { ifMauEntry 11 }




Beili                       Standards Track                    [Page 26]


RFC 4836                        MAU MIB                       April 2007


      ifMauAutoNegSupported OBJECT-TYPE
          SYNTAX      TruthValue
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "This object indicates whether or not
                      auto-negotiation is supported on this MAU."
          ::= { ifMauEntry 12 }

      ifMauTypeListBits OBJECT-TYPE
          SYNTAX      IANAifMauTypeListBits
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "A value that uniquely identifies the set of
                      possible IEEE 802.3 types that the MAU could be.
                      If auto-negotiation is present on this MAU, this
                      object will map to ifMauAutoNegCapabilityBits.

                      Note that this MAU may be capable of operating
                      as a MAU type that is beyond the scope of this
                      MIB.  This is indicated by returning the
                      bit value bOther in addition to any bit values
                      for standard capabilities that are listed in the
                      IANAifMauTypeListBits TC."
          ::= { ifMauEntry 13 }

      ifMauHCFalseCarriers OBJECT-TYPE
          SYNTAX      Counter64
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "A count of the number of false carrier events
                      during IDLE in 100BASE-X and 1000BASE-X links.

                      For all other MAU types, this counter will
                      always indicate zero.  This counter does not
                      increment at the symbol rate.

                      This counter is a 64-bit version of
                      ifMauFalseCarriers.  Since the 32-bit version of
                      this counter can roll over very quickly,
                      management stations are advised to poll the
                      64-bit version instead, in order to avoid loss
                      of information.

                      Discontinuities in the value of this counter can
                      occur at re-initialization of the management
                      system and at other times, as indicated by the
                      value of ifCounterDiscontinuityTime."
          REFERENCE   "[IEEE802.3], 30.5.1.1.10, aFalseCarriers.



Beili                       Standards Track                    [Page 27]


RFC 4836                        MAU MIB                       April 2007


                      RFC 2863, ifCounterDiscontinuityTime."
          ::= { ifMauEntry 14 }

      -- The ifJackTable applies to MAUs attached to interfaces
      -- which have one or more external jacks (connectors).

      ifJackTable OBJECT-TYPE
          SYNTAX      SEQUENCE OF IfJackEntry
          MAX-ACCESS  not-accessible
          STATUS      current
          DESCRIPTION "Information about the external jacks attached
                      to MAUs attached to an interface."
          ::= { dot3IfMauBasicGroup 2 }

      ifJackEntry OBJECT-TYPE
          SYNTAX      IfJackEntry
          MAX-ACCESS  not-accessible
          STATUS      current
          DESCRIPTION "An entry in the table, containing information
                      about a particular jack."
          INDEX       { ifMauIfIndex,
                        ifMauIndex,
                        ifJackIndex
                      }
          ::= { ifJackTable 1 }

      IfJackEntry ::=
          SEQUENCE {
              ifJackIndex                         Integer32,
              ifJackType                          IANAifJackType
          }

      ifJackIndex OBJECT-TYPE
          SYNTAX      Integer32 (1..2147483647)
          MAX-ACCESS  not-accessible
          STATUS      current
          DESCRIPTION "This variable uniquely identifies the jack
                      described by this entry from among other jacks
                      attached to the same MAU."
          ::= { ifJackEntry 1 }

      ifJackType OBJECT-TYPE
          SYNTAX      IANAifJackType
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "The jack connector type, as it appears on the
                      outside of the system."
          ::= { ifJackEntry 2 }



Beili                       Standards Track                    [Page 28]


RFC 4836                        MAU MIB                       April 2007


      --
      -- The MAU Auto-Negotiation Table
      --

      ifMauAutoNegTable OBJECT-TYPE
          SYNTAX      SEQUENCE OF IfMauAutoNegEntry
          MAX-ACCESS  not-accessible
          STATUS      current
          DESCRIPTION "Configuration and status objects for the
                      auto-negotiation function of MAUs attached to
                      interfaces.

                      The ifMauAutoNegTable applies to systems in
                      which auto-negotiation is supported on one or
                      more MAUs attached to interfaces.  Note that if
                      auto-negotiation is present and enabled, the
                      ifMauType object reflects the result of the
                      auto-negotiation function."
          ::= { dot3IfMauAutoNegGroup 1 }

      ifMauAutoNegEntry OBJECT-TYPE
          SYNTAX      IfMauAutoNegEntry
          MAX-ACCESS  not-accessible
          STATUS      current
          DESCRIPTION "An entry in the table, containing configuration
                      and status information for the auto-negotiation
                      function of a particular MAU."
          INDEX       { ifMauIfIndex,
                        ifMauIndex
                      }
          ::= { ifMauAutoNegTable 1 }

      IfMauAutoNegEntry ::=
          SEQUENCE {
              ifMauAutoNegAdminStatus           INTEGER,
              ifMauAutoNegRemoteSignaling       INTEGER,
              ifMauAutoNegConfig                INTEGER,
              ifMauAutoNegCapability            Integer32,
              ifMauAutoNegCapAdvertised         Integer32,
              ifMauAutoNegCapReceived           Integer32,
              ifMauAutoNegRestart               INTEGER,
              ifMauAutoNegCapabilityBits        IANAifMauAutoNegCapBits,
              ifMauAutoNegCapAdvertisedBits     IANAifMauAutoNegCapBits,
              ifMauAutoNegCapReceivedBits       IANAifMauAutoNegCapBits,
              ifMauAutoNegRemoteFaultAdvertised INTEGER,
              ifMauAutoNegRemoteFaultReceived   INTEGER
          }




Beili                       Standards Track                    [Page 29]


RFC 4836                        MAU MIB                       April 2007


      ifMauAutoNegAdminStatus OBJECT-TYPE
          SYNTAX      INTEGER {
                          enabled(1),
                          disabled(2)
                      }
          MAX-ACCESS  read-write
          STATUS      current
          DESCRIPTION "Setting this object to enabled(1) will cause
                      the interface that has the auto-negotiation
                      signaling ability to be enabled.

                      If the value of this object is disabled(2) then
                      the interface will act as it would if it had no
                      auto-negotiation signaling.  Under these
                      conditions, an IEEE 802.3 MAU will immediately
                      be forced to the state indicated by the value of
                      the object ifMauDefaultType.

                      NOTE TO IMPLEMENTORS:  When
                      ifMauAutoNegAdminStatus transitions from enabled
                      to disabled, the agent implementation MUST
                      ensure that the operational type of the MAU (as
                      reported by ifMauType) correctly transitions to
                      the value specified by the ifMauDefaultType
                      object, rather than continuing to operate at the
                      value earlier determined by the auto-negotiation
                      function."
          REFERENCE   "[IEEE802.3], 30.6.1.1.2, aAutoNegAdminState,
                      and 30.6.1.2.2, acAutoNegAdminControl."
          ::= { ifMauAutoNegEntry 1 }

      ifMauAutoNegRemoteSignaling OBJECT-TYPE
          SYNTAX      INTEGER {
                          detected(1),
                          notdetected(2)
                      }
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "A value indicating whether the remote end of
                      the link is using auto-negotiation signaling.  It
                      takes the value detected(1) if and only if,
                      during the previous link negotiation, FLP Bursts
                      were received."
          REFERENCE   "[IEEE802.3], 30.6.1.1.3,
                      aAutoNegRemoteSignaling."
          ::= { ifMauAutoNegEntry 2 }

      ifMauAutoNegConfig OBJECT-TYPE



Beili                       Standards Track                    [Page 30]


RFC 4836                        MAU MIB                       April 2007


          SYNTAX      INTEGER {
                          other(1),
                          configuring(2),
                          complete(3),
                          disabled(4),
                          parallelDetectFail(5)
                      }
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "A value indicating the current status of the
                      auto-negotiation process.  The enumeration
                      parallelDetectFail(5) maps to a failure in
                      parallel detection as defined in 28.2.3.1 of
                      [IEEE802.3]."
          REFERENCE   "[IEEE802.3], 30.6.1.1.4, aAutoNegAutoConfig."
          ::= { ifMauAutoNegEntry 4 }

      ifMauAutoNegCapability OBJECT-TYPE
          SYNTAX      Integer32
          MAX-ACCESS  read-only
          STATUS      deprecated
          DESCRIPTION "********* THIS OBJECT IS DEPRECATED **********

                      This object has been deprecated in favour of
                      ifMauAutoNegCapabilityBits.

                      A value that uniquely identifies the set of
                      capabilities of the local auto-negotiation
                      entity.  The value is a sum that initially
                      takes the value zero.  Then, for each capability
                      of this interface, 2 raised to the power noted
                      below is added to the sum.  For example, an
                      interface that has the capability to support
                      only 100Base-TX half duplex would have a value
                      of 32768 (2**15).  In contrast, an interface
                      that supports both 100Base-TX half duplex and
                      100Base-TX full duplex would have a value of
                      98304 ((2**15) + (2**16)).

                      The powers of 2 assigned to the capabilities are
                      these:

                      Power   Capability
                        0       other or unknown
                       (1-9)    (reserved)
                       10       10BASE-T  half duplex mode
                       11       10BASE-T  full duplex mode
                       12       (reserved)



Beili                       Standards Track                    [Page 31]


RFC 4836                        MAU MIB                       April 2007


                       13       (reserved)
                       14       100BASE-T4
                       15       100BASE-TX half duplex mode
                       16       100BASE-TX full duplex mode
                       17       (reserved)
                       18       (reserved)
                       19      100BASE-T2 half duplex mode
                       20      100BASE-T2 full duplex mode

                      Note that interfaces that support this MIB may
                      have capabilities that extend beyond the scope
                      of this MIB."
          REFERENCE   "[IEEE802.3], 30.6.1.1.5,
                      aAutoNegLocalTechnologyAbility."
          ::= { ifMauAutoNegEntry 5 }

      ifMauAutoNegCapAdvertised OBJECT-TYPE
          SYNTAX      Integer32
          MAX-ACCESS  read-write
          STATUS      deprecated
          DESCRIPTION "********* THIS OBJECT IS DEPRECATED **********

                      This object has been deprecated in favour of
                      ifMauAutoNegCapAdvertisedBits.

                      A value that uniquely identifies the set of
                      capabilities advertised by the local
                      auto-negotiation entity. Refer to
                      ifMauAutoNegCapability for a description of the
                      possible values of this object.

                      Capabilities in this object that are not
                      available in ifMauAutoNegCapability cannot be
                      enabled."
          REFERENCE   "[IEEE802.3], 30.6.1.1.6,
                      aAutoNegAdvertisedTechnologyAbility."
          ::= { ifMauAutoNegEntry 6 }

      ifMauAutoNegCapReceived OBJECT-TYPE
          SYNTAX      Integer32
          MAX-ACCESS  read-only
          STATUS      deprecated
          DESCRIPTION "********* THIS OBJECT IS DEPRECATED **********

                      This object has been deprecated in favour of
                      ifMauAutoNegCapReceivedBits.

                      A value that uniquely identifies the set of



Beili                       Standards Track                    [Page 32]


RFC 4836                        MAU MIB                       April 2007


                      capabilities received from the remote
                      auto-negotiation entity. Refer to
                      ifMauAutoNegCapability for a description of the
                      possible values of this object.

                      Note that interfaces that support this MIB may
                      be attached to remote auto-negotiation entities
                      that have capabilities beyond the scope of this
                      MIB."
          REFERENCE   "[IEEE802.3], 30.6.1.1.7,
                      aAutoNegReceivedTechnologyAbility."
          ::= { ifMauAutoNegEntry 7 }

      ifMauAutoNegRestart OBJECT-TYPE
          SYNTAX      INTEGER {
                          restart(1),
                          norestart(2)
                      }
          MAX-ACCESS  read-write
          STATUS      current
          DESCRIPTION "If the value of this object is set to
                      restart(1) then this will force auto-negotiation
                      to begin link renegotiation.  If auto-negotiation
                      signaling is disabled, a write to this object
                      has no effect.
                      Setting the value of this object to norestart(2)
                      has no effect."
          REFERENCE   "[IEEE802.3], 30.6.1.2.1,
                      acAutoNegRestartAutoConfig."
          ::= { ifMauAutoNegEntry 8 }

      ifMauAutoNegCapabilityBits OBJECT-TYPE
          SYNTAX      IANAifMauAutoNegCapBits
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "A value that uniquely identifies the set of
                      capabilities of the local auto-negotiation
                      entity.  Note that interfaces that support this
                      MIB may have capabilities that extend beyond the
                      scope of this MIB.

                      Note that the local auto-negotiation entity may
                      support some capabilities beyond the scope of
                      this MIB.  This is indicated by returning the
                      bit value bOther in addition to any bit values
                      for standard capabilities that are listed in the
                      IANAifMauAutoNegCapBits TC."




Beili                       Standards Track                    [Page 33]


RFC 4836                        MAU MIB                       April 2007


          REFERENCE   "[IEEE802.3], 30.6.1.1.5,
                      aAutoNegLocalTechnologyAbility."
          ::= { ifMauAutoNegEntry 9 }

      ifMauAutoNegCapAdvertisedBits OBJECT-TYPE
          SYNTAX      IANAifMauAutoNegCapBits
          MAX-ACCESS  read-write
          STATUS      current
          DESCRIPTION "A value that uniquely identifies the set of
                      capabilities advertised by the local
                      auto-negotiation entity.

                      Capabilities in this object that are not
                      available in ifMauAutoNegCapabilityBits cannot
                      be enabled.

                      Note that the local auto-negotiation entity may
                      advertise some capabilities beyond the scope of
                      this MIB.  This is indicated by returning the
                      bit value bOther in addition to any bit values
                      for standard capabilities that are listed in the
                      IANAifMauAutoNegCapBits TC."
          REFERENCE   "[IEEE802.3], 30.6.1.1.6,
                      aAutoNegAdvertisedTechnologyAbility."
          ::= { ifMauAutoNegEntry 10 }

      ifMauAutoNegCapReceivedBits OBJECT-TYPE
          SYNTAX      IANAifMauAutoNegCapBits
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "A value that uniquely identifies the set of
                      capabilities received from the remote
                      auto-negotiation entity.
                      Note that interfaces that support this MIB may
                      be attached to remote auto-negotiation entities
                      that have capabilities beyond the scope of this
                      MIB.  This is indicated by returning the bit
                      value bOther in addition to any bit values for
                      standard capabilities that are listed in the
                      IANAifMauAutoNegCapBits TC."
          REFERENCE   "[IEEE802.3], 30.6.1.1.7,
                      aAutoNegReceivedTechnologyAbility."
          ::= { ifMauAutoNegEntry 11 }

      ifMauAutoNegRemoteFaultAdvertised OBJECT-TYPE
          SYNTAX      INTEGER {
                          noError(1),
                          offline(2),



Beili                       Standards Track                    [Page 34]


RFC 4836                        MAU MIB                       April 2007


                          linkFailure(3),
                          autoNegError(4)
                      }
          MAX-ACCESS  read-write
          STATUS      current
          DESCRIPTION "A value that identifies any local fault
                      indications that this MAU has detected and will
                      advertise at the next auto-negotiation
                      interaction for 1000Mbps MAUs."
          REFERENCE   "[IEEE802.3], 30.6.1.1.6,
                      aAutoNegAdvertisedTechnologyAbility."
          ::= { ifMauAutoNegEntry 12 }

      ifMauAutoNegRemoteFaultReceived OBJECT-TYPE
          SYNTAX      INTEGER {
                          noError(1),
                          offline(2),
                          linkFailure(3),
                          autoNegError(4)
                      }
          MAX-ACCESS  read-only
          STATUS      current
          DESCRIPTION "A value that identifies any fault indications
                      received from the far end of a link by the
                      local auto-negotiation entity for 1000Mbps
                      MAUs."
          REFERENCE   "[IEEE802.3], 30.6.1.1.7,
                      aAutoNegReceivedTechnologyAbility."
          ::= { ifMauAutoNegEntry 13 }


      --
      -- The Basic Broadband MAU Table
      --

      broadMauBasicTable OBJECT-TYPE
          SYNTAX      SEQUENCE OF BroadMauBasicEntry
          MAX-ACCESS  not-accessible
          STATUS      deprecated
          DESCRIPTION "********* THIS OBJECT IS DEPRECATED **********

                      This entire table has been deprecated.  There
                      have been no reported implementations of this
                      table, and it is unlikely that there ever will
                      be.  IEEE recommends that broadband MAU types
                      should not be used for new installations.

                      Table of descriptive and status information



Beili                       Standards Track                    [Page 35]


RFC 4836                        MAU MIB                       April 2007


                      about the broadband MAUs connected to
                      interfaces."
          ::= { dot3BroadMauBasicGroup 1 }

      broadMauBasicEntry OBJECT-TYPE
          SYNTAX      BroadMauBasicEntry
          MAX-ACCESS  not-accessible
          STATUS      deprecated
          DESCRIPTION "********* THIS OBJECT IS DEPRECATED **********

                      An entry in the table, containing information
                      about a single broadband MAU."
          INDEX       { broadMauIfIndex,
                        broadMauIndex
                      }
          ::= { broadMauBasicTable 1 }

      BroadMauBasicEntry ::=
          SEQUENCE {
              broadMauIfIndex                     InterfaceIndex,
              broadMauIndex                       Integer32,
              broadMauXmtRcvSplitType             INTEGER,
              broadMauXmtCarrierFreq              Integer32,
              broadMauTranslationFreq             Integer32
          }

      broadMauIfIndex OBJECT-TYPE
          SYNTAX      InterfaceIndex
          MAX-ACCESS  read-only  -- read-only since originally an
                                 -- SMIv1 index
          STATUS      deprecated
          DESCRIPTION "********* THIS OBJECT IS DEPRECATED **********

                      This variable uniquely identifies the interface
                      to which the MAU described by this entry is
                      connected."
          REFERENCE   "RFC 2863, ifIndex."
          ::= { broadMauBasicEntry 1 }

      broadMauIndex OBJECT-TYPE
          SYNTAX      Integer32 (1..2147483647)
          MAX-ACCESS  read-only  -- read-only since originally an
                                 -- SMIv1 index
          STATUS      deprecated
          DESCRIPTION "********* THIS OBJECT IS DEPRECATED **********

                      This variable uniquely identifies the MAU
                      connected to interface broadMauIfIndex that is



Beili                       Standards Track                    [Page 36]


RFC 4836                        MAU MIB                       April 2007


                      described by this entry."
          REFERENCE   "[IEEE802.3], 30.5.1.1.1, aMAUID."
          ::= { broadMauBasicEntry 2 }

      broadMauXmtRcvSplitType OBJECT-TYPE
          SYNTAX      INTEGER {
                          other(1),
                          single(2),
                          dual(3)
                      }
          MAX-ACCESS  read-only
          STATUS      deprecated
          DESCRIPTION "********* THIS OBJECT IS DEPRECATED **********

                      This object indicates the type of frequency
                      multiplexing/cabling system used to separate the
                      transmit and receive paths for the 10BROAD36
                      MAU.

                      The value other(1) is returned if the split type
                      is not either single or dual.

                      The value single(2) indicates a single cable
                      system.  The value dual(3) indicates a dual
                      cable system, offset normally zero."
          REFERENCE   "[IEEE802.3], 30.5.1.1.8, aBbMAUXmitRcvSplitType."
          ::= { broadMauBasicEntry 3 }

      broadMauXmtCarrierFreq OBJECT-TYPE
          SYNTAX      Integer32
          MAX-ACCESS  read-only
          STATUS      deprecated
          DESCRIPTION "********* THIS OBJECT IS DEPRECATED **********

                      This variable indicates the transmit carrier
                      frequency of the 10BROAD36 MAU in MHz/4; that
                      is, in units of 250 kHz."
          REFERENCE   "[IEEE802.3], 30.5.1.1.9,
                      aBroadbandFrequencies.xmitCarrierFrequency."
          ::= { broadMauBasicEntry 4 }

      broadMauTranslationFreq OBJECT-TYPE
          SYNTAX      Integer32
          MAX-ACCESS  read-only
          STATUS      deprecated
          DESCRIPTION "********* THIS OBJECT IS DEPRECATED **********

                      This variable indicates the translation offset



Beili                       Standards Track                    [Page 37]


RFC 4836                        MAU MIB                       April 2007


                      frequency of the 10BROAD36 MAU in MHz/4; that
                      is, in units of 250 kHz."
          REFERENCE   "[IEEE802.3], 30.5.1.1.9,
                      aBroadbandFrequencies.translationFrequency."
          ::= { broadMauBasicEntry 5 }

      -- Notifications for use by 802.3 MAUs

      snmpDot3MauTraps OBJECT IDENTIFIER ::= { snmpDot3MauMgt 0 }

      rpMauJabberTrap NOTIFICATION-TYPE
          OBJECTS     { rpMauJabberState }
          STATUS      current
          DESCRIPTION "This trap is sent whenever a managed repeater
                      MAU enters the jabber state.

                      The agent MUST throttle the generation of
                      consecutive rpMauJabberTraps so that there is at
                      least a five-second gap between them."
          REFERENCE   "[IEEE802.3], 30.5.1.3.1, nJabber notification."
          ::= { snmpDot3MauTraps 1 }

      ifMauJabberTrap NOTIFICATION-TYPE
          OBJECTS     { ifMauJabberState }
          STATUS      current
          DESCRIPTION "This trap is sent whenever a managed interface
                      MAU enters the jabber state.

                      The agent MUST throttle the generation of
                      consecutive ifMauJabberTraps so that there is at
                      least a five-second gap between them."

          REFERENCE   "[IEEE802.3], 30.5.1.3.1, nJabber notification."
          ::= { snmpDot3MauTraps 2 }

      -- Conformance information

      mauModConf
              OBJECT IDENTIFIER ::= { mauMod 1 }
        mauModCompls
              OBJECT IDENTIFIER ::= { mauModConf 1 }
        mauModObjGrps
              OBJECT IDENTIFIER ::= { mauModConf 2 }
        mauModNotGrps
              OBJECT IDENTIFIER ::= { mauModConf 3 }

      -- Object groups




Beili                       Standards Track                    [Page 38]


RFC 4836                        MAU MIB                       April 2007


      mauRpGrpBasic OBJECT-GROUP
          OBJECTS     { rpMauGroupIndex,
                        rpMauPortIndex,
                        rpMauIndex,
                        rpMauType,
                        rpMauStatus,
                        rpMauMediaAvailable,
                        rpMauMediaAvailableStateExits,
                        rpMauJabberState,
                        rpMauJabberingStateEnters
                      }
          STATUS      current
          DESCRIPTION "Basic conformance group for MAUs attached to
                      repeater ports.  This group is also the
                      conformance specification for RFC 1515
                      implementations."
          ::= { mauModObjGrps 1 }

      mauRpGrp100Mbs OBJECT-GROUP
          OBJECTS     { rpMauFalseCarriers }
          STATUS      current
          DESCRIPTION "Conformance group for MAUs attached to
                      repeater ports with 100 Mb/s or greater
                      capability."
          ::= { mauModObjGrps 2 }

      mauRpGrpJack OBJECT-GROUP
          OBJECTS     { rpJackType }
          STATUS      current
          DESCRIPTION "Conformance group for MAUs attached to
                      repeater ports with managed jacks."
          ::= { mauModObjGrps 3 }

      mauIfGrpBasic OBJECT-GROUP
          OBJECTS     { ifMauIfIndex,
                        ifMauIndex,
                        ifMauType,
                        ifMauStatus,
                        ifMauMediaAvailable,
                        ifMauMediaAvailableStateExits,
                        ifMauJabberState,
                        ifMauJabberingStateEnters
                      }
          STATUS      current
          DESCRIPTION "Basic conformance group for MAUs attached to
                      interfaces.  This group also provides a
                      conformance specification for RFC 1515
                      implementations."



Beili                       Standards Track                    [Page 39]


RFC 4836                        MAU MIB                       April 2007


          ::= { mauModObjGrps 4 }

      mauIfGrp100Mbs OBJECT-GROUP
          OBJECTS     { ifMauFalseCarriers,
                        ifMauTypeList,
                        ifMauDefaultType,
                        ifMauAutoNegSupported
                      }

          STATUS      deprecated
          DESCRIPTION "********* THIS GROUP IS DEPRECATED **********

                      Conformance group for MAUs attached to
                      interfaces with 100 Mb/s capability.

                      This object group has been deprecated in favor
                      of mauIfGrpHighCapacity."
          ::= { mauModObjGrps 5 }

      mauIfGrpJack OBJECT-GROUP
          OBJECTS     { ifJackType }
          STATUS      current
          DESCRIPTION "Conformance group for MAUs attached to
                      interfaces with managed jacks."
          ::= { mauModObjGrps 6 }

      mauIfGrpAutoNeg OBJECT-GROUP
          OBJECTS     { ifMauAutoNegAdminStatus,
                        ifMauAutoNegRemoteSignaling,
                        ifMauAutoNegConfig,
                        ifMauAutoNegCapability,
                        ifMauAutoNegCapAdvertised,
                        ifMauAutoNegCapReceived,
                        ifMauAutoNegRestart
                      }
          STATUS      deprecated
          DESCRIPTION "********* THIS GROUP IS DEPRECATED **********

                      Conformance group for MAUs attached to
                      interfaces with managed auto-negotiation.

                      This object group has been deprecated in favor
                      of mauIfGrpAutoNeg2."
          ::= { mauModObjGrps 7 }

      mauBroadBasic OBJECT-GROUP
          OBJECTS     { broadMauIfIndex,
                        broadMauIndex,



Beili                       Standards Track                    [Page 40]


RFC 4836                        MAU MIB                       April 2007


                        broadMauXmtRcvSplitType,
                        broadMauXmtCarrierFreq,
                        broadMauTranslationFreq
                      }
          STATUS      deprecated
          DESCRIPTION "********* THIS GROUP IS DEPRECATED **********
                      Conformance group for broadband MAUs attached
                      to interfaces.

                      This object group is deprecated.  There have
                      been no reported implementations of this group,
                      and it was felt to be unlikely that there will
                      be any future implementations."
          ::= { mauModObjGrps 8 }

      mauIfGrpHighCapacity OBJECT-GROUP
          OBJECTS     { ifMauFalseCarriers,
                        ifMauTypeListBits,
                        ifMauDefaultType,
                        ifMauAutoNegSupported
                      }
          STATUS      current
          DESCRIPTION "Conformance group for MAUs attached to
                      interfaces with 100 Mb/s or greater capability."
          ::= { mauModObjGrps 9 }

      mauIfGrpAutoNeg2 OBJECT-GROUP
          OBJECTS     { ifMauAutoNegAdminStatus,
                        ifMauAutoNegRemoteSignaling,
                        ifMauAutoNegConfig,
                        ifMauAutoNegCapabilityBits,
                        ifMauAutoNegCapAdvertisedBits,
                        ifMauAutoNegCapReceivedBits,
                        ifMauAutoNegRestart
                      }
          STATUS      current
          DESCRIPTION "Conformance group for MAUs attached to
                      interfaces with managed auto-negotiation."
          ::= { mauModObjGrps 10 }

      mauIfGrpAutoNeg1000Mbps OBJECT-GROUP
          OBJECTS     { ifMauAutoNegRemoteFaultAdvertised,
                        ifMauAutoNegRemoteFaultReceived
                      }
          STATUS      current
          DESCRIPTION "Conformance group for 1000Mbps MAUs attached to
                      interfaces with managed auto-negotiation."
          ::= { mauModObjGrps 11 }



Beili                       Standards Track                    [Page 41]


RFC 4836                        MAU MIB                       April 2007


      mauIfGrpHCStats OBJECT-GROUP
          OBJECTS     { ifMauHCFalseCarriers }
          STATUS      current
          DESCRIPTION "Conformance for high capacity statistics for
                      MAUs attached to interfaces."
          ::= { mauModObjGrps 12 }

      -- Notification groups

      rpMauNotifications NOTIFICATION-GROUP
          NOTIFICATIONS { rpMauJabberTrap }
          STATUS      current
          DESCRIPTION "Notifications for repeater MAUs."
          ::= { mauModNotGrps 1 }

      ifMauNotifications NOTIFICATION-GROUP
          NOTIFICATIONS { ifMauJabberTrap }
          STATUS      current
          DESCRIPTION "Notifications for interface MAUs."
          ::= { mauModNotGrps 2 }

      -- Compliances

      mauModRpCompl MODULE-COMPLIANCE
          STATUS      deprecated
          DESCRIPTION "******** THIS COMPLIANCE IS DEPRECATED ********
                      Compliance for MAUs attached to repeater
                      ports.

                      This compliance is deprecated and replaced by
                      mauModRpCompl2, which corrects an oversight by
                      allowing rpMauStatus to be implemented
                      read-only."

          MODULE -- this module
              MANDATORY-GROUPS { mauRpGrpBasic }

              GROUP       mauRpGrp100Mbs
              DESCRIPTION "Implementation of this optional group is
                          recommended for MAUs that have 100Mb/s or
                          greater capability."

              GROUP       mauRpGrpJack
              DESCRIPTION "Implementation of this optional group is
                          recommended for MAUs that have one or more
                          external jacks."

              GROUP       rpMauNotifications



Beili                       Standards Track                    [Page 42]


RFC 4836                        MAU MIB                       April 2007


              DESCRIPTION "Implementation of this group is recommended
                          for MAUs attached to repeater ports."
          ::= { mauModCompls 1 }

      mauModIfCompl MODULE-COMPLIANCE
          STATUS      deprecated
          DESCRIPTION "******** THIS COMPLIANCE IS DEPRECATED ********

                      Compliance for MAUs attached to interfaces.
                      This compliance is deprecated and replaced by
                      mauModIfCompl2."

          MODULE -- this module
              MANDATORY-GROUPS { mauIfGrpBasic }

              GROUP       mauIfGrp100Mbs
              DESCRIPTION "Implementation of this optional group is
                          recommended for MAUs that have 100Mb/s
                          capability."

              GROUP       mauIfGrpJack
              DESCRIPTION "Implementation of this optional group is
                          recommended for MAUs that have one or more
                          external jacks."

              GROUP       mauIfGrpAutoNeg
              DESCRIPTION "Implementation of this group is mandatory
                          for MAUs that support managed
                          auto-negotiation."

              GROUP       mauBroadBasic
              DESCRIPTION "Implementation of this group is mandatory
                          for broadband MAUs."

              GROUP       ifMauNotifications
              DESCRIPTION "Implementation of this group is recommended
                          for MAUs attached to interfaces."
          ::= { mauModCompls 2 }

      mauModIfCompl2 MODULE-COMPLIANCE
          STATUS      deprecated
          DESCRIPTION "******** THIS COMPLIANCE IS DEPRECATED ********

                      Compliance for MAUs attached to interfaces.

                      This compliance is deprecated and replaced by
                      mauModIfCompl3."




Beili                       Standards Track                    [Page 43]


RFC 4836                        MAU MIB                       April 2007


          MODULE -- this module
              MANDATORY-GROUPS { mauIfGrpBasic }

              GROUP       mauIfGrpHighCapacity
              DESCRIPTION "Implementation of this optional group is
                          recommended for MAUs that have 100Mb/s
                          or greater capability."

              GROUP       mauIfGrpJack

              DESCRIPTION "Implementation of this optional group is
                          recommended for MAUs that have one or more
                          external jacks."

              GROUP       mauIfGrpAutoNeg2
              DESCRIPTION "Implementation of this group is mandatory
                          for MAUs that support managed
                          auto-negotiation."

              GROUP       mauIfGrpAutoNeg1000Mbps
              DESCRIPTION "Implementation of this group is mandatory
                          for MAUs that have 1000Mb/s or greater
                          capability and support managed
                          auto-negotiation."

              GROUP       ifMauNotifications
              DESCRIPTION "Implementation of this group is recommended
                          for MAUs attached to interfaces."

              OBJECT      ifMauStatus
              MIN-ACCESS  read-only
              DESCRIPTION "Write access is not required."
          ::= { mauModCompls 3 }

      mauModRpCompl2 MODULE-COMPLIANCE
          STATUS      current
          DESCRIPTION "Compliance for MAUs attached to repeater
                      ports.

                      Note that compliance with this compliance
                      statement requires compliance with the
                      snmpRptrModCompl MODULE-COMPLIANCE statement of
                      the SNMP-REPEATER-MIB (RFC 2108)."

          MODULE -- this module
              MANDATORY-GROUPS { mauRpGrpBasic }

              GROUP       mauRpGrp100Mbs



Beili                       Standards Track                    [Page 44]


RFC 4836                        MAU MIB                       April 2007


              DESCRIPTION "Implementation of this optional group is
                          recommended for MAUs that have 100Mb/s or
                          greater capability."

              GROUP       mauRpGrpJack
              DESCRIPTION "Implementation of this optional group is
                          recommended for MAUs that have one or more
                          external jacks."

              GROUP       rpMauNotifications

              DESCRIPTION "Implementation of this group is recommended
                          for MAUs attached to repeater ports."

              OBJECT      rpMauStatus
              MIN-ACCESS  read-only
              DESCRIPTION "Write access is not required."
          ::= { mauModCompls 4 }

      mauModIfCompl3 MODULE-COMPLIANCE
          STATUS      current
          DESCRIPTION "Compliance for MAUs attached to interfaces.

                      Note that compliance with this compliance
                      statement requires compliance with the
                      ifCompliance3 MODULE-COMPLIANCE statement of the
                      IF-MIB (RFC 2863) and the dot3Compliance2
                      MODULE-COMPLIANCE statement of the
                      EtherLike-MIB (RFC3635)."

          MODULE -- this module
              MANDATORY-GROUPS { mauIfGrpBasic }

              GROUP       mauIfGrpHighCapacity
              DESCRIPTION "Implementation of this optional group is
                          recommended for MAUs that have 100Mb/s
                          or greater capability."

              GROUP       mauIfGrpHCStats
              DESCRIPTION "Implementation of this group is mandatory
                          for MAUs that have 1000Mb/s capacity, and
                          is recommended for MAUs that have 100Mb/s
                          capacity."

              GROUP       mauIfGrpJack
              DESCRIPTION "Implementation of this optional group is
                          recommended for MAUs that have one or more
                          external jacks."



Beili                       Standards Track                    [Page 45]


RFC 4836                        MAU MIB                       April 2007


              GROUP       mauIfGrpAutoNeg2
              DESCRIPTION "Implementation of this group is mandatory
                          for MAUs that support managed
                          auto-negotiation."
              GROUP       mauIfGrpAutoNeg1000Mbps
              DESCRIPTION "Implementation of this group is mandatory
                          for MAUs that have 1000Mb/s or greater
                          capability and support managed
                          auto-negotiation."

              GROUP       ifMauNotifications
              DESCRIPTION "Implementation of this group is recommended
                          for MAUs attached to interfaces."

              OBJECT      ifMauStatus
              MIN-ACCESS  read-only
              DESCRIPTION "Write access is not required."
          ::= { mauModCompls 5 }

   END

5.  IANA-Maintained MAU TC Definitions

   IANA-MAU-MIB DEFINITIONS ::= BEGIN

     IMPORTS
       MODULE-IDENTITY, OBJECT-IDENTITY, mib-2
         FROM SNMPv2-SMI
       TEXTUAL-CONVENTION
         FROM SNMPv2-TC
       ;

     ianaMauMIB MODULE-IDENTITY
       LAST-UPDATED "200704210000Z"  -- April 21, 2007
       ORGANIZATION "IANA"
       CONTACT-INFO "        Internet Assigned Numbers Authority

                     Postal: ICANN
                             4676 Admiralty Way, Suite 330
                             Marina del Rey, CA 90292

                        Tel: +1-310-823-9358
                      EMail: iana@iana.org"

       DESCRIPTION
         "This MIB module defines dot3MauType OBJECT-IDENTITIES and
         IANAifMauListBits, IANAifMauMediaAvailable,
         IANAifMauAutoNegCapBits, and IANAifJackType



Beili                       Standards Track                    [Page 46]


RFC 4836                        MAU MIB                       April 2007


         TEXTUAL-CONVENTIONs, specifying enumerated values of the
         ifMauTypeListBits, ifMauMediaAvailable / rpMauMediaAvailable,
         ifMauAutoNegCapabilityBits / ifMauAutoNegCapAdvertisedBits /
         ifMauAutoNegCapReceivedBits and ifJackType / rpJackType objects
         respectively, defined in the MAU-MIB.

         It is intended that each new MAU type, Media Availability
         state, Auto Negotiation capability and/or Jack type defined by
         the IEEE 802.3 working group and approved for publication in a
         revision of IEEE Std 802.3 will be added to this MIB module,
         provided that it is suitable for being managed by the base
         objects in the MAU-MIB.  An Expert Review, as defined in
         RFC 2434 [RFC2434], is REQUIRED for such additions.

         The following reference is used throughout this MIB module:

         [IEEE802.3] refers to:
            IEEE Std 802.3, 2005 Edition: 'IEEE Standard for
            Information technology - Telecommunications and information
            exchange between systems - Local and metropolitan area
            networks - Specific requirements -
            Part 3: Carrier sense multiple access with collision
            detection (CSMA/CD) access method and physical layer
            specifications'.

         This reference should be updated as appropriate when new
         MAU types, Media Availability states, Auto Negotiation
         capabilities, and/or Jack types are added to this MIB module.

         Copyright (C) The IETF Trust (2007).
         The initial version of this MIB module was published in
         RFC 4836; for full legal notices see the RFC itself.
         Supplementary information may be available at:
         http://www.ietf.org/copyrights/ianamib.html"

       REVISION     "200704210000Z"  -- April 21, 2007
       DESCRIPTION  "Initial version of this MIB as published in
                     RFC 4836."
       ::= { mib-2 154 }

     -- Textual Conventions

     IANAifMauTypeListBits ::= TEXTUAL-CONVENTION
       STATUS       current
       DESCRIPTION
         "This data type is used as the syntax of the ifMauTypeListBits
         object in the (updated) definition of MAU-MIB's ifMauTable.




Beili                       Standards Track                    [Page 47]


RFC 4836                        MAU MIB                       April 2007


         The most recent version of this textual convention is available
         in the online version of this MIB module on the IANA web site.

         Requests for new values should be made to IANA via email
         (iana@iana.org).

         Note that changes in this textual convention SHALL be
         synchronized with relevant changes in the dot3MauType
         OBJECT-IDENTITIES."
       REFERENCE
         "[IEEE802.3], Section 30.5.1.1.2"
       SYNTAX       BITS {
              bOther(0),          -- other or unknown
              bAUI(1),            -- AUI
              b10base5(2),        -- 10BASE-5
              bFoirl(3),          -- FOIRL

              b10base2(4),        -- 10BASE-2
              b10baseT(5),        -- 10BASE-T duplex mode unknown
              b10baseFP(6),       -- 10BASE-FP
              b10baseFB(7),       -- 10BASE-FB
              b10baseFL(8),       -- 10BASE-FL duplex mode unknown
              b10broad36(9),      -- 10BROAD36
              b10baseTHD(10),     -- 10BASE-T  half duplex mode
              b10baseTFD(11),     -- 10BASE-T  full duplex mode
              b10baseFLHD(12),    -- 10BASE-FL half duplex mode
              b10baseFLFD(13),    -- 10BASE-FL full duplex mode
              b100baseT4(14),     -- 100BASE-T4
              b100baseTXHD(15),   -- 100BASE-TX half duplex mode
              b100baseTXFD(16),   -- 100BASE-TX full duplex mode
              b100baseFXHD(17),   -- 100BASE-FX half duplex mode
              b100baseFXFD(18),   -- 100BASE-FX full duplex mode
              b100baseT2HD(19),   -- 100BASE-T2 half duplex mode
              b100baseT2FD(20),   -- 100BASE-T2 full duplex mode

              b1000baseXHD(21),   -- 1000BASE-X half duplex mode
              b1000baseXFD(22),   -- 1000BASE-X full duplex mode
              b1000baseLXHD(23),  -- 1000BASE-LX half duplex mode
              b1000baseLXFD(24),  -- 1000BASE-LX full duplex mode
              b1000baseSXHD(25),  -- 1000BASE-SX half duplex mode
              b1000baseSXFD(26),  -- 1000BASE-SX full duplex mode
              b1000baseCXHD(27),  -- 1000BASE-CX half duplex mode
              b1000baseCXFD(28),  -- 1000BASE-CX full duplex mode
              b1000baseTHD(29),   -- 1000BASE-T half duplex mode
              b1000baseTFD(30),   -- 1000BASE-T full duplex mode

              b10GbaseX(31),      -- 10GBASE-X
              b10GbaseLX4(32),    -- 10GBASE-LX4



Beili                       Standards Track                    [Page 48]


RFC 4836                        MAU MIB                       April 2007


              b10GbaseR(33),      -- 10GBASE-R
              b10GbaseER(34),     -- 10GBASE-ER
              b10GbaseLR(35),     -- 10GBASE-LR
              b10GbaseSR(36),     -- 10GBASE-SR
              b10GbaseW(37),      -- 10GBASE-W
              b10GbaseEW(38),     -- 10GBASE-EW
              b10GbaseLW(39),     -- 10GBASE-LW
              b10GbaseSW(40),     -- 10GBASE-SW
              -- new since RFC 3636
              b10GbaseCX4(41),    -- 10GBASE-CX4
              b2BaseTL(42),       -- 2BASE-TL
              b10PassTS(43),      -- 10PASS-TS
              b100BaseBX10D(44),  -- 100BASE-BX10D
              b100BaseBX10U(45),  -- 100BASE-BX10U
              b100BaseLX10(46),   -- 100BASE-LX10
              b1000BaseBX10D(47), -- 1000BASE-BX10D
              b1000BaseBX10U(48), -- 1000BASE-BX10U
              b1000BaseLX10(49),  -- 1000BASE-LX10
              b1000BasePX10D(50), -- 1000BASE-PX10D
              b1000BasePX10U(51), -- 1000BASE-PX10U
              b1000BasePX20D(52), -- 1000BASE-PX20D
              b1000BasePX20U(53)  -- 1000BASE-PX20U
         }

     IANAifMauMediaAvailable ::= TEXTUAL-CONVENTION
       STATUS       current
       DESCRIPTION
         "This data type is used as the syntax of the
         ifMauMediaAvailable and rpMauMediaAvailable objects in the
         (updated) definition of MAU-MIB's ifMauTable and rpMauTable
         respectively.

         Possible values are:
           other(1)             - undefined (not listed below)
           unknown(2)           - MAU's true state is unknown; e.g.,
                                  during initialization
           available(3)         - link, light, or loopback is normal
           notAvailable(4)      - link loss, low light, or no loopback
           remoteFault(5)       - a fault has been detected at the
                                  remote end of the link.  This value
                                  applies to 10BASE-FB, 100BASE-T4 Far
                                  End Fault Indication and non-specified
                                  remote faults from a system running
                                  auto-negotiation
           invalidSignal(6)     - invalid signal has been received from
                                  the other end of the link, 10BASE-FB
                                  only
           remoteJabber(7)      - remote fault, due to jabber



Beili                       Standards Track                    [Page 49]


RFC 4836                        MAU MIB                       April 2007


           remoteLinkLoss(8)    - remote fault, due to link loss
           remoteTest(9)        - remote fault, due to test
           offline(10)          - offline, Clause 37 Auto-Negotiation
                                  only
           autoNegError(11)     - Auto-Negotiation Error, Clause 37
                                  Auto-Negotiation only
           pmdLinkFault(12)     - PMA/PMD receive link fault.  In case
                                  of PAF (2BASE-TL / 10PASS-TS PHYs),
                                  all PMEs in the aggregation group have
                                  detected a link fault
           wisFrameLoss(13)     - WIS loss of frame, 10GBASE-W only
           wisSignalLoss(14)    - WIS loss of signal, 10GBASE-W only
           pcsLinkFault(15)     - PCS receive link fault
           excessiveBER(16)     - PCS Bit Error Ratio monitor
                                  reporting excessive error ratio
           dxsLinkFault(17)     - DTE XGXS receive link fault, XAUI only
           pxsLinkFault(18)     - PHY XGXS receive link fault, XAUI only
           availableReduced(19) - link normal, reduced bandwidth,
                                  2BASE-TL / 10PASS-TS only
           ready(20)            - at least one PME in the aggregation
                                  group is detecting handshake tones,
                                  2BASE-TL / 10PASS-TS only

         If the MAU is a 10M b/s link or fiber type (FOIRL, 10BASE-T,
         10BASE-F), then this is equivalent to the link test fail
         state/low light function.  For an AUI, 10BASE2, 10BASE5, or
         10BROAD36 MAU, this indicates whether loopback is detected on
         the DI circuit.  The value of this attribute persists between
         packets for MAU types AUI, 10BASE5, 10BASE2, 10BROAD36, and
         10BASEFP.

         At power-up or following a reset, the Media Available state
         will be unknown(2) for AUI, 10BASE5, 10BASE2, 10BROAD36, and
         10BASE-FP MAUs.  For these MAUs loopback will be tested on each
         transmission during which no collision is detected.
         If DI is receiving input when DO returns to IDL after a
         transmission and there has been no collision during the
         transmission, then loopback will be detected.  The Media
         Available state will only change during noncollided
         transmissions for AUI, 10BASE2, 10BASE5, 10BROAD36, and
         10BASE-FP MAUs.

         For 100BASE-T2, 100BASE-T4, 100BASE-TX, 100BASE-FX,
         100BASE-LX10, and 100BASE-BX10 PHYs the enumerations match the
         states within the link integrity state diagram.
         Any MAU that implements management of [IEEE802.3] Clause
         28 Auto-Negotiation, will map remote fault indication to
         remoteFault(5).



Beili                       Standards Track                    [Page 50]


RFC 4836                        MAU MIB                       April 2007


         Any MAU that implements management of Clause 37
         Auto-Negotiation, will map the received RF1 and RF2 bits as
         follows: Offline maps to offline(10), Link_Failure maps to
         remoteFault(5), and Auto-Negotiation Error maps to
         autoNegError(11).

         The value remoteFault(5) applies to 10BASE-FB remote
         fault indication, the 100BASE-X far-end fault indication, and
         nonspecified remote faults from a system running Clause 28
         Auto-Negotiation.

         The value remoteJabber(7), remoteLink loss(8), or remoteTest(9)
         SHOULD be used instead of remoteFault(5) where the reason for
         remote fault is identified in the remote signaling protocol.
         Where a Clause 22 MII or Clause 35 GMII is present, a logic
         one in the remote fault bit maps to the value remoteFault(5),
         a logic zero in the link status bit maps to the enumeration
         notAvailable(4).  The value notAvailable(4) takes precedence
         over remoteFault(5).

         For 2BASE-TL and 10PASS-TS PHYs, the value unknown(2) maps to
         the condition where the PHY (PCS with connected PMEs) is
         initializing, the value ready(20) maps to the condition where
         the interface is down and at least one PME in the aggregation
         group is ready for handshake, the value available(3) maps to
         the condition where all the PMEs in the aggregation group are
         up, the value notAvailable(4) maps to the condition where all
         the PMEs in the aggregation group are down and no handshake
         tones are detected, the value availableReduced(19) maps to the
         condition where the interface is up, a link fault is detected
         at the receive direction by one or more PMEs in the
         aggregation group, but at least one PME is up and the
         enumeration pmdLinkFault(12) maps to the condition where a link
         fault is detected at the receive direction by all of the PMEs
         in the aggregation group.

         For 10 Gb/s the enumerations map to value of the link_fault
         variable within the Link Fault Signaling state diagram
         as follows: the value OK maps to the value available(3),
         the value Local Fault maps to the value notAvailable(4),
         and the value Remote Fault maps to the value remoteFault(5).
         The value pmdLinkFault(12), wisFrameLoss(13),
         wisSignalLoss(14), pcsLinkFault(15), excessiveBER(16), or
         dxsLinkFault(17) SHOULD be used instead of the value
         notAvailable(4), where the reason for the Local Fault state can
         be identified through the use of the Clause 45 MDIO Interface.
         Where multiple reasons for the Local Fault state can be
         identified, only the highest precedence error SHOULD be



Beili                       Standards Track                    [Page 51]


RFC 4836                        MAU MIB                       April 2007


         reported.  This precedence in descending order is as follows:

           pxsLinkFault
           pmdLinkFault
           wisFrameLoss
           wisSignalLoss
           pcsLinkFault
           excessiveBER
           dxsLinkFault.

         Where a Clause 45 MDIO interface is present a logic zero in
         the PMA/PMD Receive link status bit ([IEEE802.3]
         Section 45.2.1.2.2) maps to the value pmdLinkFault(12),
         logic one in the LOF status bit (Section 45.2.2.10.4) maps
         to the value wisFrameLoss(13), a logic one in the LOS
         status bit (Section 45.2.2.10.5) maps to the value
         wisSignalLoss, a logic zero in the PCS Receive
         link status bit (Section 45.2.3.2.2) maps to the value
         pcsLinkFault(15), a logic one in the 10GBASE-R PCS Latched
         high BER status bit (Section 45.2.3.12.2) maps to the value
         excessiveBER, a logic zero in the DTE XS receive link status
         bit (Section 45.2.5.2.2) maps to the value dxsLinkFault(17)
         and a logic zero in the PHY XS transmit link status bit
         (Section 45.2.4.2.2) maps to the value pxsLinkFault(18).

         The most recent version of this textual convention is available
         in the online version of this MIB module on the IANA web site.

         Requests for new values should be made to IANA via email
         (iana@iana.org)."
       REFERENCE
         "[IEEE802.3], Section 30.5.1.1.4"
       SYNTAX       INTEGER {
              other(1),
              unknown(2),
              available(3),
              notAvailable(4),
              remoteFault(5),
              invalidSignal(6),
              remoteJabber(7),
              remoteLinkLoss(8),
              remoteTest(9),
              offline(10),
              autoNegError(11),
              pmdLinkFault(12),
              wisFrameLoss(13),
              wisSignalLoss(14),
              pcsLinkFault(15),



Beili                       Standards Track                    [Page 52]


RFC 4836                        MAU MIB                       April 2007


              excessiveBER(16),
              dxsLinkFault(17),
              pxsLinkFault(18),
              availableReduced(19),
              ready(20)
         }

     IANAifMauAutoNegCapBits ::= TEXTUAL-CONVENTION
       STATUS       current
       DESCRIPTION
         "This data type is used as the syntax of the
         ifMauAutoNegCapabilityBits, ifMauAutoNegCapAdvertisedBits, and
         ifMauAutoNegCapReceivedBits objects in the (updated) definition
         of MAU-MIB's ifMauAutoNegTable.

         The most recent version of this textual convention is available
         in the online version of this MIB module on the IANA web site.

         Requests for new values should be made to IANA via email
         (iana@iana.org)."
       REFERENCE
         "[IEEE802.3], Section 30.6.1.1.5"
       SYNTAX       BITS {
              bOther(0),          -- other or unknown
              b10baseT(1),        -- 10BASE-T  half duplex mode
              b10baseTFD(2),      -- 10BASE-T  full duplex mode
              b100baseT4(3),      -- 100BASE-T4
              b100baseTX(4),      -- 100BASE-TX half duplex mode
              b100baseTXFD(5),    -- 100BASE-TX full duplex mode
              b100baseT2(6),      -- 100BASE-T2 half duplex mode
              b100baseT2FD(7),    -- 100BASE-T2 full duplex mode
              bFdxPause(8),       -- PAUSE for full-duplex links
              bFdxAPause(9),      -- Asymmetric PAUSE for full-duplex
                                  --     links
              bFdxSPause(10),     -- Symmetric PAUSE for full-duplex
                                  --     links
              bFdxBPause(11),     -- Asymmetric and Symmetric PAUSE for
                                  --     full-duplex links
              b1000baseX(12),     -- 1000BASE-X, -LX, -SX, -CX half
                                  --     duplex mode
              b1000baseXFD(13),   -- 1000BASE-X, -LX, -SX, -CX full
                                  --     duplex mode
              b1000baseT(14),     -- 1000BASE-T half duplex mode
              b1000baseTFD(15)    -- 1000BASE-T full duplex mode
         }

     IANAifJackType ::= TEXTUAL-CONVENTION
       STATUS       current



Beili                       Standards Track                    [Page 53]


RFC 4836                        MAU MIB                       April 2007


       DESCRIPTION
         "Common enumeration values for repeater and interface MAU
         jack types.  This data type is used as the syntax of the
         ifJackType and rpJackType objects in the (updated) definition
         of MAU-MIB's ifJackTable and rpJackTable respectively.

         Possible values are:
              other(1)          - undefined or unknown
              rj45(2)           - RJ45
              rj45S(3)          - RJ45 shielded
              db9(4)            - DB9
              bnc(5)            - BNC
              fAUI(6)           - AUI female
              mAUI(7)           - AUI male
              fiberSC(8)        - SC fiber
              fiberMIC(9)       - MIC fiber
              fiberST(10)       - ST fiber
              telco(11)         - Telco
              mtrj(12)          - MT-RJ fiber
              hssdc(13)         - fiber channel style-2
              fiberLC(14)       - LC fiber
              cx4(15)           - IB4X for 10GBASE-CX4

         The most recent version of this textual convention is available
         in the online version of this MIB module on the IANA web site.

         Requests for new values should be made to IANA via email
         (iana@iana.org)."
       SYNTAX       INTEGER {
              other(1),
              rj45(2),
              rj45S(3),
              db9(4),
              bnc(5),
              fAUI(6),
              mAUI(7),
              fiberSC(8),
              fiberMIC(9),
              fiberST(10),
              telco(11),
              mtrj(12),
              hssdc(13),
              fiberLC(14),
              -- new since RFC 3636
              cx4(15)
         }

     -- OBJECT IDENTITIES for MAU types



Beili                       Standards Track                    [Page 54]


RFC 4836                        MAU MIB                       April 2007


     --  (see rpMauType and ifMauType of MAU-MIB for usage)
     -- The following definitions has been moved from RFC 3636 and
     -- no longer appear in its revision.

     dot3MauType OBJECT IDENTIFIER ::= { mib-2 snmpDot3MauMgt(26) 4 }

     dot3MauTypeAUI OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "no internal MAU, view from AUI"
       REFERENCE   "[IEEE802.3], Section 7"
       ::= { dot3MauType 1 }

     dot3MauType10Base5 OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "thick coax MAU"
       REFERENCE   "[IEEE802.3], Section 7"
       ::= { dot3MauType 2 }

     dot3MauTypeFoirl OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "FOIRL MAU"
       REFERENCE   "[IEEE802.3], Section 9.9"
       ::= { dot3MauType 3 }

     dot3MauType10Base2 OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "thin coax MAU"
       REFERENCE   "[IEEE802.3], Section 10"
       ::= { dot3MauType 4 }

     dot3MauType10BaseT OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "UTP MAU.
                   Note that it is strongly recommended that
                   agents return either dot3MauType10BaseTHD or
                   dot3MauType10BaseTFD if the duplex mode is
                   known.  However, management applications should
                   be prepared to receive this MAU type value from
                   older agent implementations."
       REFERENCE   "[IEEE802.3], Section 14"
       ::= { dot3MauType 5 }

     dot3MauType10BaseFP OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "passive fiber MAU"
       REFERENCE   "[IEEE802.3], Section 16"
       ::= { dot3MauType 6 }




Beili                       Standards Track                    [Page 55]


RFC 4836                        MAU MIB                       April 2007


     dot3MauType10BaseFB OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "sync fiber MAU"
       REFERENCE   "[IEEE802.3], Section 17"
       ::= { dot3MauType 7 }

     dot3MauType10BaseFL OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "async fiber MAU.
                   Note that it is strongly recommended that
                   agents return either dot3MauType10BaseFLHD or
                   dot3MauType10BaseFLFD if the duplex mode is
                   known.  However, management applications should
                   be prepared to receive this MAU type value from
                   older agent implementations."
       REFERENCE   "[IEEE802.3], Section 18"
       ::= { dot3MauType 8 }

     dot3MauType10Broad36 OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "broadband DTE MAU.
                   Note that 10BROAD36 MAUs can be attached to
                   interfaces but not to repeaters."
       REFERENCE   "[IEEE802.3], Section 11"
       ::= { dot3MauType 9 }

     ------ new since RFC 1515:
     dot3MauType10BaseTHD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "UTP MAU, half duplex mode"
       REFERENCE   "[IEEE802.3], Section 14"
       ::= { dot3MauType 10 }

     dot3MauType10BaseTFD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "UTP MAU, full duplex mode"
       REFERENCE   "[IEEE802.3], Section 14"
       ::= { dot3MauType 11 }

     dot3MauType10BaseFLHD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "async fiber MAU, half duplex mode"
       REFERENCE   "[IEEE802.3], Section 18"
       ::= { dot3MauType 12 }

     dot3MauType10BaseFLFD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "async fiber MAU, full duplex mode"



Beili                       Standards Track                    [Page 56]


RFC 4836                        MAU MIB                       April 2007


       REFERENCE   "[IEEE802.3], Section 18"
       ::= { dot3MauType 13 }

     dot3MauType100BaseT4 OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "4 pair category 3 UTP"
       REFERENCE   "[IEEE802.3], Section 23"
       ::= { dot3MauType 14 }

     dot3MauType100BaseTXHD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "2 pair category 5 UTP, half duplex mode"
       REFERENCE   "[IEEE802.3], Section 25"
       ::= { dot3MauType 15 }

     dot3MauType100BaseTXFD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "2 pair category 5 UTP, full duplex mode"
       REFERENCE   "[IEEE802.3], Section 25"
       ::= { dot3MauType 16 }

     dot3MauType100BaseFXHD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "X fiber over PMT, half duplex mode"
       REFERENCE   "[IEEE802.3], Section 26"
       ::= { dot3MauType 17 }

     dot3MauType100BaseFXFD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "X fiber over PMT, full duplex mode"
       REFERENCE   "[IEEE802.3], Section 26"
       ::= { dot3MauType 18 }

     dot3MauType100BaseT2HD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "2 pair category 3 UTP, half duplex mode"
       REFERENCE   "[IEEE802.3], Section 32"
       ::= { dot3MauType 19 }

     dot3MauType100BaseT2FD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "2 pair category 3 UTP, full duplex mode"
       REFERENCE   "[IEEE802.3], Section 32"
       ::= { dot3MauType 20 }

     ------ new since RFC 2239:
     dot3MauType1000BaseXHD OBJECT-IDENTITY
       STATUS      current



Beili                       Standards Track                    [Page 57]


RFC 4836                        MAU MIB                       April 2007


       DESCRIPTION "PCS/PMA, unknown PMD, half duplex mode"
       REFERENCE   "[IEEE802.3], Section 36"
       ::= { dot3MauType 21 }

     dot3MauType1000BaseXFD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "PCS/PMA, unknown PMD, full duplex mode"
       REFERENCE   "[IEEE802.3], Section 36"
       ::= { dot3MauType 22 }

     dot3MauType1000BaseLXHD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "Fiber over long-wavelength laser, half duplex
                   mode"
       REFERENCE   "[IEEE802.3], Section 38"
       ::= { dot3MauType 23 }

     dot3MauType1000BaseLXFD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "Fiber over long-wavelength laser, full duplex
                   mode"
       REFERENCE   "[IEEE802.3], Section 38"
       ::= { dot3MauType 24 }

     dot3MauType1000BaseSXHD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "Fiber over short-wavelength laser, half
                   duplex mode"
       REFERENCE   "[IEEE802.3], Section 38"
       ::= { dot3MauType 25 }

     dot3MauType1000BaseSXFD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "Fiber over short-wavelength laser, full
                   duplex mode"
       REFERENCE   "[IEEE802.3], Section 38"
       ::= { dot3MauType 26 }

     dot3MauType1000BaseCXHD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "Copper over 150-Ohm balanced cable, half
                   duplex mode"
       REFERENCE   "[IEEE802.3], Section 39"
       ::= { dot3MauType 27 }

     dot3MauType1000BaseCXFD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "Copper over 150-Ohm balanced cable, full



Beili                       Standards Track                    [Page 58]


RFC 4836                        MAU MIB                       April 2007


                   duplex mode"
       REFERENCE   "[IEEE802.3], Section 39"
       ::= { dot3MauType 28 }

     dot3MauType1000BaseTHD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "Four-pair Category 5 UTP, half duplex mode"
       REFERENCE   "[IEEE802.3], Section 40"
       ::= { dot3MauType 29 }

     dot3MauType1000BaseTFD OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "Four-pair Category 5 UTP, full duplex mode"
       REFERENCE   "[IEEE802.3], Section 40"
       ::= { dot3MauType 30 }

     ------ new since RFC 2668:
     dot3MauType10GigBaseX OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "X PCS/PMA, unknown PMD."
       REFERENCE   "[IEEE802.3], Section 48"
       ::= { dot3MauType 31 }

     dot3MauType10GigBaseLX4 OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "X fiber over WWDM optics"
       REFERENCE   "[IEEE802.3], Section 53"
       ::= { dot3MauType 32 }

     dot3MauType10GigBaseR OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "R PCS/PMA, unknown PMD."
       REFERENCE   "[IEEE802.3], Section 49"
       ::= { dot3MauType 33 }

     dot3MauType10GigBaseER OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "R fiber over 1550 nm optics"
       REFERENCE   "[IEEE802.3], Section 52"
       ::= { dot3MauType 34 }

     dot3MauType10GigBaseLR OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "R fiber over 1310 nm optics"
       REFERENCE   "[IEEE802.3], Section 52"
       ::= { dot3MauType 35 }

     dot3MauType10GigBaseSR OBJECT-IDENTITY



Beili                       Standards Track                    [Page 59]


RFC 4836                        MAU MIB                       April 2007


       STATUS      current
       DESCRIPTION "R fiber over 850 nm optics"
       REFERENCE   "[IEEE802.3], Section 52"
       ::= { dot3MauType 36 }

     dot3MauType10GigBaseW OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "W PCS/PMA, unknown PMD."
       REFERENCE   "[IEEE802.3], Section 49 and 50"
       ::= { dot3MauType 37 }

     dot3MauType10GigBaseEW OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "W fiber over 1550 nm optics"
       REFERENCE   "[IEEE802.3], Section 52"
       ::= { dot3MauType 38 }

     dot3MauType10GigBaseLW OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "W fiber over 1310 nm optics"
       REFERENCE   "[IEEE802.3], Section 52"
       ::= { dot3MauType 39 }

     dot3MauType10GigBaseSW OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "W fiber over 850 nm optics"
       REFERENCE   "[IEEE802.3], Section 52"
       ::= { dot3MauType 40 }

     ------ new since RFC 3636:
     dot3MauType10GigBaseCX4 OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "X copper over 8 pair 100-Ohm balanced cable"
       REFERENCE   "[IEEE802.3], Section 54"
       ::= { dot3MauType 41 }

     dot3MauType2BaseTL OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "Voice grade UTP copper, up to 2700m, optional PAF"
       REFERENCE   "[IEEE802.3], Sections 61 and 63"
       ::= { dot3MauType 42 }

     dot3MauType10PassTS OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "Voice grade UTP copper, up to 750m, optional PAF"
       REFERENCE   "[IEEE802.3], Sections 61 and 62"
       ::= { dot3MauType 43 }




Beili                       Standards Track                    [Page 60]


RFC 4836                        MAU MIB                       April 2007


     dot3MauType100BaseBX10D OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "One single-mode fiber OLT, long wavelength, 10km"
       REFERENCE   "[IEEE802.3], Section 58"
       ::= { dot3MauType 44 }

     dot3MauType100BaseBX10U OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "One single-mode fiber ONU, long wavelength, 10km"
       REFERENCE   "[IEEE802.3], Section 58"
       ::= { dot3MauType 45 }

     dot3MauType100BaseLX10 OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "Two single-mode fibers, long wavelength, 10km"
       REFERENCE   "[IEEE802.3], Section 58"
       ::= { dot3MauType 46 }

     dot3MauType1000BaseBX10D OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "One single-mode fiber OLT, long wavelength, 10km"
       REFERENCE   "[IEEE802.3], Section 59"
       ::= { dot3MauType 47 }

     dot3MauType1000BaseBX10U OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "One single-mode fiber ONU, long wavelength, 10km"
       REFERENCE   "[IEEE802.3], Section 59"
       ::= { dot3MauType 48 }

     dot3MauType1000BaseLX10 OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "Two sigle-mode fiber, long wavelength, 10km"
       REFERENCE   "[IEEE802.3], Section 59"
       ::= { dot3MauType 49 }

     dot3MauType1000BasePX10D OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "One single-mode fiber EPON OLT, 10km"
       REFERENCE   "[IEEE802.3], Section 60"
       ::= { dot3MauType 50 }

     dot3MauType1000BasePX10U OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "One single-mode fiber EPON ONU, 10km"
       REFERENCE   "[IEEE802.3], Section 60"
       ::= { dot3MauType 51 }




Beili                       Standards Track                    [Page 61]


RFC 4836                        MAU MIB                       April 2007


     dot3MauType1000BasePX20D OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "One single-mode fiber EPON OLT, 20km"
       REFERENCE   "[IEEE802.3], Section 60"
       ::= { dot3MauType 52 }

     dot3MauType1000BasePX20U OBJECT-IDENTITY
       STATUS      current
       DESCRIPTION "One single-mode fiber EPON ONU, 20km"
       REFERENCE   "[IEEE802.3], Section 60"
       ::= { dot3MauType 53 }

   END

6.  Security Considerations

   The IANA-MAU-MIB does not define any management objects.  Instead, it
   defines a set of textual conventions which are used by the MAU-MIB
   and may be used by other MIB modules to define management objects.
   Meaningful security considerations can only be written for MIB
   modules that define management objects.

   There are a number of management objects defined in the MAU-MIB that
   have a MAX-ACCESS clause of read-write.  Setting these objects can
   have a serious effect on the operation of the network, including:

   o  enabling or disabling a MAU

   o  changing a MAU's default type

   o  enabling, disabling, or restarting autonegotiation

   o  modifying the capabilities that a MAU advertizes during
      autonegotiation.

   Such objects may be considered sensitive or vulnerable in some
   network environments.  The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations.

   Some of the readable objects in the MAU-MIB module (i.e., objects
   with a MAX-ACCESS other than not-accessible) may be considered
   sensitive or vulnerable in some network environments.  In some
   environments, it may be undesirable to allow unauthorized parties to
   access statistics or status information about individual links in a
   network.  It is thus important to control even GET and/or NOTIFY
   access to these objects and possibly to even encrypt the values of
   these objects when sending them over the network via SNMP.



Beili                       Standards Track                    [Page 62]


RFC 4836                        MAU MIB                       April 2007


   SNMP versions prior to SNMPv3 did not include adequate security.
   Even if the network itself is secure (for example by using IPsec),
   even then, there is no control as to who on the secure network is
   allowed to access and GET/SET (read/change/create/delete) the objects
   in the MAU-MIB module.

   It is RECOMMENDED that the implementors consider the security
   features as provided by the SNMPv3 framework (see [RFC3410], section
   8), including full support for the SNMPv3 cryptographic mechanisms
   (for authentication and privacy).

   Furthermore, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED.  Instead, it is RECOMMENDED to deploy SNMPv3 and to
   enable cryptographic security.  It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of the MAU-MIB module is properly configured to give access
   to the objects only to those principals (users) that have legitimate
   rights to indeed GET or SET (change/create/delete) them.

7.  IANA Considerations

   This document defines first version of the IANA-maintained IANA-MAU-
   MIB module.  It is intended that each new MAU type, Media Available
   state, Auto Negotiation capability, and/or Jack type defined by the
   IEEE 802.3 working group and approved for publication in a revision
   of IEEE Std 802.3 will be added to the IANA-maintaned MIB module,
   provided that it is suitable for being managed by the base objects in
   the MAU-MIB module.

   For each new MAU type added, a short description of the MAU
   technology and, wherever possible, a reference to a publicly
   available specification SHOULD be specified.  An Expert Review, as
   defined in RFC 2434 [RFC2434], is REQUIRED, for each modification.

8.  Acknowledgments

   This document was produced by the IETF Ethernet Interfaces and Hub
   MIB Working Group, whose efforts were greatly advanced by the
   contributions of the following people:

      Mike Heard

      John Flick

      Dan Romascanu

   This document is based on the Proposed Standard MAU MIB, RFC 3636
   [RFC3636], edited by John Flick of Hewlett-Packard, and produced by



Beili                       Standards Track                    [Page 63]


RFC 4836                        MAU MIB                       April 2007


   the Ethernet Interfaces and Hub MIB Working Group.  It extends that
   document by moving the object identities and textual conventions for
   MAU types into a IANA-maintained MIB module.  In addition, support is
   provided for the EFM and 10GBASE-CX4 MAUs as defined in [IEEE802.3ah]
   and [IEEE802.3ak] respectively.

   RFC 3636, in turn, was based on the Proposed Standard MAU MIB, RFC
   2668 [RFC2668], edited by John Flick of Hewlett-Packard and Andrew
   Smith, then of Extreme Networks, and produced by the Ethernet
   Interfaces and Hub MIB Working Group.  It extends that document by
   providing support for 10 Gb/s MAUs as defined in [IEEE802.3ae].

   RFC 2668, in turn, was based on the Proposed Standard MAU MIB, RFC
   2239 [RFC2239], edited by Kathryn de Graaf, then of 3Com, and Dan
   Romascanu, then of Madge Networks, and produced by the Ethernet
   Interfaces and Hub MIB Working Group.  It extended that document by
   providing support for 1000 Mb/sec MAUs, PAUSE negotiation and remote
   fault status as defined in [IEEE802.3].

   RFC 2239, in turn, was based on the Proposed Standard MAU MIB, RFC
   1515 [RFC1515], edited by Donna McMaster, then of SynOptics
   Communications, Keith McCloghrie, then of Hughes LAN Systems, and Sam
   Roberts, then of Farallon Computing, and produced by the Hub MIB
   Working Group.  It extends that document by providing support for 100
   Mb/sec MAUs, full duplex MAUs, auto-negotiation, and jack management
   as defined in [IEEE802.3].

9.  References

9.1.  Normative References

   [IEEE802.3]    IEEE, "IEEE Standard for Information technology -
                  Telecommunications and information exchange between
                  systems - Local and metropolitan area networks -
                  Specific requirements - Part 3: Carrier sense multiple
                  access with collision detection (CSMA/CD) access
                  method and physical layer specifications", IEEE
                  Std 802.3-2005, December 2005.

   [IEEE802.3ae]  IEEE, "IEEE Standard for Information technology -
                  Telecommunications and information exchange between
                  systems - Local and metropolitan area networks -
                  Specific requirements - Part 3: Carrier sense multiple
                  access with collision detection (CSMA/CD) access
                  method and physical layer specifications - Media
                  Access Control (MAC) Parameters, Physical Layer and
                  Management Parameters for 10 Gb/s Operation", IEEE
                  Std 802.3ae-2002, August 2002.



Beili                       Standards Track                    [Page 64]


RFC 4836                        MAU MIB                       April 2007


   [IEEE802.3ah]  IEEE, "Information technology - Telecommunications and
                  information exchange between systems - Local and
                  metropolitan area networks - Specific requirements -
                  Part 3: Carrier sense multiple access with collision
                  detection (CSMA/CD) access method and physical layer
                  specifications - Media Access Control Parameters,
                  Physical Layers and Management Parameters for
                  Subscriber Access Networks", IEEE Std 802.3ah-2004,
                  September 2004.

   [IEEE802.3ak]  IEEE, "IEEE Standard for Information technology -
                  Telecommunications and information exchange between
                  systems - Local and metropolitan area networks -
                  Specific requirements - Part 3: Carrier sense multiple
                  access with collision detection (CSMA/CD) access
                  method and physical layer specifications - Physical
                  Layer and Management Parameters for 10Gb/s Operation,
                  Type 10GBASE-CX4", IEEE Std 802.3ak-2004, March 2004.

   [RFC2108]      de Graaf, K., Romascanu, D., McMaster, D., and K.
                  McCloghrie, "Definitions of Managed Objects for IEEE
                  802.3 Repeater Devices using SMIv2", RFC 2108,
                  February 1997.

   [RFC2119]      Bradner, S., "Key words for use in RFCs to Indicate
                  Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2434]      Narten, T. and H. Alvestrand, "Guidelines for Writing
                  an IANA Considerations Section in RFCs", BCP 26,
                  RFC 2434, October 1998.

   [RFC2578]      McCloghrie, K., Ed., Perkins, D., Ed., and J.
                  Schoenwaelder, Ed., "Structure of Management
                  Information Version 2 (SMIv2)", STD 58, RFC 2578,
                  April 1999.

   [RFC2579]      McCloghrie, K., Ed., Perkins, D., Ed., and J.
                  Schoenwaelder, Ed., "Textual Conventions for SMIv2",
                  STD 58, RFC 2579, April 1999.

   [RFC2580]      McCloghrie, K., Perkins, D., and J. Schoenwaelder,
                  "Conformance Statements for SMIv2", STD 58, RFC 2580,
                  April 1999.

   [RFC2863]      McCloghrie, K. and F. Kastenholz, "The Interfaces
                  Group MIB", RFC 2863, June 2000.





Beili                       Standards Track                    [Page 65]


RFC 4836                        MAU MIB                       April 2007


   [RFC3635]      Flick, J., "Definitions of Managed Objects for the
                  Ethernet-like Interface Types", RFC 3635,
                  September 2003.

9.2.  Informative References

   [RFC1515]      McMaster, D., McCloghrie, K., and S. Roberts,
                  "Definitions of Managed Objects for IEEE 802.3 Medium
                  Attachment Units (MAUs)", RFC 1515, September 1993.

   [RFC2239]      de Graaf, K., Romascanu, D., McMaster, D., McCloghrie,
                  K., and S. Roberts, "Definitions of Managed Objects
                  for IEEE 802.3 Medium Attachment Units (MAUs) using
                  SMIv2", RFC 2239, November 1997.

   [RFC2668]      Smith, A., Flick, J., de Graaf, K., Romascanu, D.,
                  McMaster, D., McCloghrie, K., and S. Roberts,
                  "Definitions of Managed Objects for IEEE 802.3 Medium
                  Attachment Units (MAUs)", RFC 2668, August 1999.

   [RFC3410]      Case, J., Mundy, R., Partain, D., and B. Stewart,
                  "Introduction and Applicability Statements for
                  Internet-Standard Management Framework", RFC 3410,
                  December 2002.

   [RFC3418]      Presuhn, R., "Management Information Base (MIB) for
                  the Simple Network Management Protocol (SNMP)",
                  STD 62, RFC 3418, December 2002.

   [RFC3636]      Flick, J., "Definitions of Managed Objects for IEEE
                  802.3 Medium Attachment Units (MAUs)", RFC 3636,
                  September 2003.

   [RFC3637]      Heard, C., "Definitions of Managed Objects for the
                  Ethernet WAN Interface Sublayer", RFC 3637,
                  September 2003.

Author's Address

   Edward Beili
   Actelis Networks
   Bazel 25
   Petach-Tikva
   Israel

   Phone: +972-3-924-3491
   EMail: edward.beili@actelis.com




Beili                       Standards Track                    [Page 66]


RFC 4836                        MAU MIB                       April 2007


Full Copyright Statement

   Copyright (C) The IETF Trust (2007).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
   THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
   OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.







Beili                       Standards Track                    [Page 67]